bizhub 600 feed issue.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • chocolab
    Technician
    • Jan 2012
    • 10
    #1

    bizhub 600 feed issue.

    hello everyone,
    i have a bizhub 600 that will try to feed paper then pop a message that says " open tray 1 rail and reload paper stack"
    i swapped the feed unit with tray 2 and the problem followed the unit to tray 2. i swapped sensors around but it isn't
    any of the sensors. another tech replaced the clutches and rollers a week ago. i cant find anything on this on kmbs website.
    iany help would be appreciated. thanks in advance.
    Tags: None
    • RRodgers
      Service Manager

      1,000+ Posts
      • Jun 2009
      • 1950
      #2
      Re: bizhub 600 feed issue.

      Originally posted by chocolab
      hello everyone,
      i have a bizhub 600 that will try to feed paper then pop a message that says " open tray 1 rail and reload paper stack"
      i swapped the feed unit with tray 2 and the problem followed the unit to tray 2. i swapped sensors around but it isn't
      any of the sensors. another tech replaced the clutches and rollers a week ago. i cant find anything on this on kmbs website.
      iany help would be appreciated. thanks in advance.
      When he replaced the rollers did he change just the rubber or did he replace the whole hub with the rubber as well?
      Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it.

        Comment

        • chocolab
          Technician
          • Jan 2012
          • 10
          #3
          im not really sure, but will ask him tomorrow

            Comment

            • JustManuals
              Field Supervisor

              5,000+ Posts
              • Jan 2006
              • 9919
              #4
              Re: bizhub 600 feed issue.

              This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from:


              Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


              Paul@justmanuals.com

                Comment

                • chocolab
                  Technician
                  • Jan 2012
                  • 10
                  #5
                  talked to tech and he said he replaced rubber with hub.

                    Comment

                    • RRodgers
                      Service Manager

                      1,000+ Posts
                      • Jun 2009
                      • 1950
                      #6
                      Re: bizhub 600 feed issue.

                      check to be sure that the shafts that the one ways ride on are not glazed over. If so use some scotch bright to scuff them up.
                      Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it.

                        Comment

                        • fixthecopier
                          ALIEN OVERLORD

                          2,500+ Posts
                          • Apr 2008
                          • 4714
                          #7
                          Re: bizhub 600 feed issue.

                          Originally posted by RRodgers
                          check to be sure that the shafts that the one ways ride on are not glazed over. If so use some scotch bright to scuff them up.

                          Please tell me more
                          The greatest enemy of knowledge isn't ignorance, it is the illusion of knowledge. Stephen Hawking

                            Comment

                            • Mr Spock
                              Vulcan Inventor of Death

                              1,000+ Posts
                              • Aug 2006
                              • 2064
                              #8
                              Re: bizhub 600 feed issue.

                              There is a bulletin about feed issues on this style of feeder. Not sure if it covers this model. The roller that feeds the paper out of the unit (conv roller under the metal cover on right side). has been know to wear prematurely and cause the paper to hit the idler instead of the nip. This causes it to not feed in a timely manner. They updated the roller and idlers. I will see if I can find the bulletin.
                              And Star Trek was just a tv show...yeah right!

                                Comment

                                • chocolab
                                  Technician
                                  • Jan 2012
                                  • 10
                                  #9
                                  i ordered the whole feed unit, will update after i put it in.

                                    Comment

                                    • chocolab
                                      Technician
                                      • Jan 2012
                                      • 10
                                      #10
                                      didnt want to putz with it anymore so i just replaced the feed unit, and that did take care of it.

                                        Comment

                                        Previous template Next
                                        Working...