J15-01 on Bizhub C220

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • xscotty1990
    Technician
    • Nov 2013
    • 40
    #1

    J15-01 on Bizhub C220

    Hello Folks out there,

    i got a problem with a bizhub c220.

    There is a paper jam between the red feeding rollers after around 20 till 40 Sheets. Jam Code says J15-01.
    We have already changed the feeding tires, one way clutches and Separation roller and nothing helped.

    I think the next step would be to change the feeding motor of the LCT....

    Is there someone who had the same jam code ?

    Greetings

    Marco
    Tags: bizhub, code, jam, jam code, motor, paper, paper jam, problem, sheets
    • blackcat4866
      Master Of The Obvious
      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22545
      #2
      Re: J15-01 on Bizhub C220

      You wouldn't happen to be feeding Comet brand paper from a PC-408, tray #3? This is a strange situation, but for me, affected 60+ machines:

      Misfeeds (1501) from tray #3 (PC-408) only, with 350 sheets or less in the right side of the tray, right in the bite of the feed/separation rollers. Standard letter sized paper is 279mm. Comet brand paper is 280.4mm, which fits a little too snuggly front to rear, causing the lift plate to tip to the right at the top of it's lift. To replicate the problem remove tray front face and lift motor. Manually lift the tray to observe tipping. Theory: paper stalls when the left side of the stack presses against the top of the feed unit. Loosen the four right side screws to spread the front and rear frames/guides an additional 1.25mm (the remaining screw hole clearance). Snug screws.

      It's a longshot, but how about this? =^..^=
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • JustManuals
          Field Supervisor
          5,000+ Posts
          • Jan 2006
          • 9932
          #3
          Re: J15-01 on Bizhub C220

          This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from:


          http://www.justmanuals.com



          paul@justmanuals.com

            Comment

            • PeterG
              Trusted Tech
              100+ Posts
              • Jul 2008
              • 177
              #4
              Re: J15-01 on Bizhub C220

              Originally posted by blackcat4866
              You wouldn't happen to be feeding Comet brand paper from a PC-408, tray #3? This is a strange situation, but for me, affected 60+ machines:

              Misfeeds (1501) from tray #3 (PC-408) only, with 350 sheets or less in the right side of the tray, right in the bite of the feed/separation rollers. Standard letter sized paper is 279mm. Comet brand paper is 280.4mm, which fits a little too snuggly front to rear, causing the lift plate to tip to the right at the top of it's lift. To replicate the problem remove tray front face and lift motor. Manually lift the tray to observe tipping. Theory: paper stalls when the left side of the stack presses against the top of the feed unit. Loosen the four right side screws to spread the front and rear frames/guides an additional 1.25mm (the remaining screw hole clearance). Snug screws.

              It's a longshot, but how about this? =^..^=
              I am going to look at a copier tomorrow that I have been chasing this problem on for 3 months. If you are correct, "me love you long time".

                Comment

                • xscotty1990
                  Technician
                  • Nov 2013
                  • 40
                  #5
                  Re: J15-01 on Bizhub C220

                  We are only using A4 Paper, no Letter Format.

                  But there could maybe a lift failure?
                  I looked for mod. on the km Website, but there was nothing specific for feeding problems from PC-408.

                  I had this jam code once before on other machines. There always some black "grease" under the oneway clutches. After removing the "grease" and changing the clutches the problem was solved.


                  Greetings

                  Marco

                    Comment

                    • xscotty1990
                      Technician
                      • Nov 2013
                      • 40
                      #6
                      Re: J15-01 on Bizhub C220

                      Hello,

                      i want to give a little feed back.

                      The problem is solved.

                      We have shorten the sensor flag from the lift sensor on LCT.
                      The sensor flag is on the paper feed unit.

                      Now the machine is running very fine.

                      greetz

                      Marco

                        Comment

                        • blackcat4866
                          Master Of The Obvious
                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 22545
                          #7
                          Re: J15-01 on Bizhub C220

                          Thanks for posting back, xscotty. =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            Previous template Next
                            Working...