When you take down a screw and you fall into the printer ...

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Bix
    Service Manager

    1,000+ Posts
    • Apr 2018
    • 1421
    #1

    When you take down a screw and you fall into the printer ...

    *it fall into the printer

    Screwdriver with magnet but sometimes it happens ...
    And when it ends, you will never know its end (praying does not end in gears or the like)
    Tags: end, ends, gears, screw
    • roho
      Senior Tech

      500+ Posts
      • Mar 2009
      • 844
      #2
      Re: When you take down a screw and you fall into the printer ...

      Originally posted by Bix
      *it fall into the printer

      Screwdriver with magnet but sometimes it happens ...
      And when it ends, you will never know its end (praying does not end in gears or the like)

      Or a power supply!!!!!!!!

        Comment

        • qbert69
          Service Manager

          1,000+ Posts
          • Mar 2013
          • 1152
          #3
          Re: When you take down a screw and you fall into the printer ...

          Originally posted by roho
          Or a power supply!!!!!!!!
          Or A Jesus Clip!!![emoji15]

          Sent from my SM-N950U1 using Tapatalk
          REACH FOR THE STARS!!!
          Konica Minolta Planetariums!
          https://www.konicaminolta.com/planet...gma/index.html

            Comment

            • blackcat4866
              Master Of The Obvious

              Site Contributor
              10,000+ Posts
              • Jul 2007
              • 23009
              #4
              Re: When you take down a screw and you fall into the printer ...

              Years back I had an operation panel screw drop into a Mita DC-2055. It sat there undisturbed for 6 years. Then one day I needed to roll the machine away from the wall. The screw had been resting quietly on a live heat sink on the lamp regulator board. When I disturbed it the screw rolled over to the front frame and made some lovely fireworks.

              Upon investigation I remembered the lost screw, and found a 75mm long trace missing from the board. As an experiment I soldered on a wire to bridge across the smoked trace ... and to my surprise it actually worked! =^..^=
              If you'd like a serious answer to your request:
              1) demonstrate that you've read the manual
              2) demonstrate that you made some attempt to fix it.
              3) if you're going to ask about jams include the jam code.
              4) if you're going to ask about an error code include the error code.
              5) You are the person onsite. Only you can make observations.

              blackcat: Master Of The Obvious =^..^=

                Comment

                • qbert69
                  Service Manager

                  1,000+ Posts
                  • Mar 2013
                  • 1152
                  #5
                  Re: When you take down a screw and you fall into the printer ...

                  Originally posted by blackcat4866
                  Years back I had an operation panel screw drop into a Mita DC-2055. It sat there undisturbed for 6 years. Then one day I needed to roll the machine away from the wall. The screw had been resting quietly on a live heat sink on the lamp regulator board. When I disturbed it the screw rolled over to the front frame and made some lovely fireworks.

                  Upon investigation I remembered the lost screw, and found a 75mm long trace missing from the board. As an experiment I soldered on a wire to bridge across the smoked trace ... and to my surprise it actually worked! =^..^=
                  You Repaired The Magick Smoak!!!....put the Genie back in the bottle!!![emoji23][emoji23][emoji23]

                  Sent from my SM-N950U1 using Tapatalk
                  REACH FOR THE STARS!!!
                  Konica Minolta Planetariums!
                  https://www.konicaminolta.com/planet...gma/index.html

                    Comment

                    Previous template Next
                    Working...