It is the technology of the copy machine in Japan.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • osamu takahashi
    Junior Member
    • Jul 2013
    • 7
    #1

    It is the technology of the copy machine in Japan.

    Nice to meet you
    We are touching the copier CANON mainly, but messing with the SHARP MX2310FN this time, and you can not reset it becomes L4-16 at the same time as the power is turned on. FUSER and also check, there is no problem especially pressure sensor. Do you have a case like this? Please forgive me strange statement because it uses the translation software.：混乱：
    Tags: canon, copier, fuser, power, reset, sharp, software, tech, time
    • Aneurysm
      Administrator

      1,000+ Posts
      • Jan 2005
      • 1030
      #2
      Welcome Aboard!
      "Remain calm. All is well." -Chip Diller, Nov 1963

        Comment

        • DWise
          Senior Tech

          500+ Posts
          • Apr 2010
          • 895
          #3
          Re: It is the technology of the copy machine in Japan.

          Welcome to CTN!!

          You should try to post your question in the Sharp forum for a better response
          ==> Sharp
          Do for one what you wished you could do for everyone. - Andy Stanley

            Comment

            • igi
              Service Manager

              1,000+ Posts
              • Apr 2009
              • 1507
              #4
              Re: It is the technology of the copy machine in Japan.

              Originally posted by osamu takahashi
              Nice to meet you
              We are touching the copier CANON mainly, but messing with the SHARP MX2310FN this time, and you can not reset it becomes L4-16 at the same time as the power is turned on. FUSER and also check, there is no problem especially pressure sensor. Do you have a case like this? Please forgive me strange statement because it uses the translation software.：混乱：
              Trouble content A change in the fusing pressure release sensor signal
              cannot be detected within the specified time after
              outputting the fusing pressure release motor.
              Detail PCU
              Cause Fusing pressure release sensor trouble.
              Fusing pressure release motor trouble.
              Pressure release drive gear and pressure release idle
              gear trouble.
              PCU PWB trouble.
              Connection trouble of the connector and the harness.
              Check & Remedy Replace the fusing pressure release sensor.
              Replace the fusing pressure release motor.
              Replace the pressure release drive gear and the
              pressure release idle gear.
              Replace the PCU PWB.
              Check connection of the connector and the harness

                Comment

                • HenryT2
                  Senior Tech

                  500+ Posts
                  • Apr 2010
                  • 962
                  #5
                  Re: It is the technology of the copy machine in Japan.

                  Welcome !!!
                  "The Serenity Prayer" . . .
                  God grant me the serenity to accept stupid people , the courage to not waste my time and energy on them , and the wisdom to know that I cannot fix STUPID .

                    Comment

                    • osamu takahashi
                      Junior Member
                      • Jul 2013
                      • 7
                      #6
                      Re: It is the technology of the copy machine in Japan.

                      Originally posted by igi
                      Trouble content A change in the fusing pressure release sensor signal
                      cannot be detected within the specified time after
                      outputting the fusing pressure release motor.
                      Detail PCU
                      Cause Fusing pressure release sensor trouble.
                      Fusing pressure release motor trouble.
                      Pressure release drive gear and pressure release idle
                      gear trouble.
                      PCU PWB trouble.
                      Connection trouble of the connector and the harness.
                      Check & Remedy Replace the fusing pressure release sensor.
                      Replace the fusing pressure release motor.
                      Replace the pressure release drive gear and the
                      pressure release idle gear.
                      Replace the PCU PWB.
                      Check connection of the connector and the harness

                      Thank you for everything. It was replaced with a new one fuser but the situation did not change. I think you try and replace the PCU substrate assembly of gear because it is also all right.
                      Thank you!

                        Comment

                        • osamu takahashi
                          Junior Member
                          • Jul 2013
                          • 7
                          #7
                          Re: It is the technology of the copy machine in Japan.

                          Originally posted by DWise
                          Welcome to CTN!!

                          You should try to post your question in the Sharp forum for a better response
                          ==> Sharp
                          Thank you.
                          I will ask in the forum of SHARP

                            Comment

                            Previous template Next
                            Working...