[CQ] ir a c3320

[imran181070]

dear all

please look at pic 1 when machine has issue only for BK, but after replacing HVT fm1-c996-000

became look at pic 2

job done


1 replaced both HVT for drum & develop biasing & hvt for transfer

2 replaced dc controller

3 power supply

4 reset DC CON

any best idea which i forgot


thanks


REGARDS

[Phil B.]

Re: ir a c3320

dear all

please look at pic 1 when machine has issue only for BK, but after replacing HVT fm1-c996-000

became look at pic 2

job done


1 replaced both HVT for drum & develop biasing & hvt for transfer

2 replaced dc controller

3 power supply

4 reset DC CON

any best idea which i forgot


thanks


REGARDS

what about the transfer assmy?

[imran181070]

Re: ir a c3320

what about the transfer assmy?

problem is sir we cant see any image or PATCHES on ITB during printing or

initialising the machine ,how ever we replaced the transfer roller assy & ITB

[mga]

Re: ir a c3320

dear all

please look at pic 1 when machine has issue only for BK, but after replacing HVT fm1-c996-000

became look at pic 2

job done


1 replaced both HVT for drum & develop biasing & hvt for transfer

2 replaced dc controller

3 power supply

4 reset DC CON

any best idea which i forgot


thanks


REGARDS

Its some thing you done when replacing hvt. What make you think it was that in the 1st place did you not 1st replace K drum and or K dev assy

[Phil B.]

Re: ir a c3320

Its some thing you done when replacing hvt. What make you think it was that in the 1st place did you not 1st replace K drum and or K dev assy

Come on Man didn't you know it's ALWAYS a board problem?

some people rather use the 'shotgun' approach to trouble shooting a problem than LOGIC!

[imran181070]

Re: ir a c3320

Its some thing you done when replacing hvt. What make you think it was that in the 1st place did you not 1st replace K drum and or K dev assy

if u know this machine well ,then u should never say so , HVT so easy to replace it has only 2 connectors

before replacing hvt we replaced drum & developer assy then we go frurther .

in copytechnet their are over smart peoples , they dont know nothing but pretend to be experts ,instead helping annoying other not u sir , at least u asked

logical question

[mga]

Re: ir a c3320

if u know this machine well ,then u should never say so , HVT so easy to replace it has only 2 connectors

before replacing hvt we replaced drum & developer assy then we go frurther .

in copytechnet their are over smart peoples , they dont know nothing but pretend to be experts ,instead helping annoying other not u sir , at least u asked

logical question

You did not say you replace drum and dev assy for the 1st picture you said you replaced when you had the 2nd fault put the machine back with original parts try and get pic 1 back if the pic2 happened after you replaced hvt you made problem worse go back over your work good luck

[Phil B.]

Re: ir a c3320

You did not say you replace drum and dev assy for the 1st picture you said you replaced when you had the 2nd fault put the machine back with original parts try and get pic 1 back if the pic2 happened after you replaced hvt you made problem worse go back over your work good luck

+1

he didn't mention he replaced the transfer UNTIL after I mentioned it.

[fchu5959]

Re: ir a c3320

dear all

please look at pic 1 when machine has issue only for BK, but after replacing HVT fm1-c996-000

became look at pic 2

job done


1 replaced both HVT for drum & develop biasing & hvt for transfer

2 replaced dc controller

3 power supply

4 reset DC CON

any best idea which i forgot


thanks


REGARDS

Indeed,this machine seems to be very simple but it can be very tricky to troubleshoot;As a fact,you should proceed logically and methodically.
You should try to get pic1 back and then proceed further.

[imran181070]

Re: ir a c3320

+1

he didn't mention he replaced the transfer until after i mentioned it.

sorry to say

better not to write on any thread

u r not help ful ,waisting ur time

[Phil B.]

Re: ir a c3320

sorry to say

better not to write on any thread

u r not help ful ,waisting ur time

uh huh look at my rep points.. I didn't get them by scratching my ass

now look at your rep points 0

I have all green cards you have nothing but red cards..

how do you get red cards?

arguing/fighting

not giving good advise to others

lying to others

not following forum rules

i came here July 2016

you came here Aug 2016

basically the same amount of time here at CTN

I rarely have to ask advise on how to fix things

in this thread alone you didn't state everything you tried to fix it... your explanation was confusing and not clearly stated

but you say I am wasting MY time? NO you are wasting OUR TIME trying to help you.

are you formally trained on any product?

I have been formally trained on: Xerox - Canon - Dell - Toshiba - KM - Mita/copyStar - HP - Samsung - OKI - Epson - FP ... all different models in each brand.

31+ years in the industry ..10 years before you started in this industry... I have been service manager in all but 1 company I worked for... I owned my own business in previous years and again now.

I don't use slang such as u for you ur for your

i spell correctly not waste ful ( it's wasteful ) waisting should be wasting

but I am in the wrong?

as the lame ass American POTUS says "Come on MAN"

I'd love to hear your customers opinions of your technical abilities and your professional attitude

when I left my last employer I had 100 customers follow me to my company .. I didn't rob or recruit them from my ex boss... they came to ME asking ME to start servicing their machines...

companies like Oxford University Press - North Carolina Attorney General - NIH - NorTel - CISCO - IBM - Glaxo Smith Cline - Durham Housing Authority - Durham PD - Harnett County Sheriff - Angier PD and Fire Dept .... plenty of print shops .. small law offices - insurance companies

you haven't made ONE friend here at CTN.... wonder why?

[Markan]

Re: ir a c3320

Hello everyone, a similar problem I had, but on a B&W printer, is that my problem was the HVT board, but even after the replacement I got a similar print, but despite that the problem was the parameters in the service mode that were changes before my work that I had to reset to factory settings. This is one idea if it is useful, and the other is sent to you in the attachment related to the replacement of the HVT board, which is according to the service bulletin. I hope that some of this will help you or at least give you another idea to solve the problem.
Change+of+the+guide+assemblies+that+fix+the+2nd+transfer+H.V.+PCB+assembly_en_02.0.pdfChange+of+the+guide+assemblies+that+fix+the+2nd+transfer+H.V.+PCB+assembly_en_02.0.pdf