IR105 finsher

[copy_suhail]

I have IR105 with error (the finisher cant use) and i see that the two trays did not checking when the machine turn on , but the finisher and stapler work ok.

thanks

[iust]

no problem

u most open finisher front door . and found small door in left side . in the case is mechanical keys u back every keys in ON mode.

[zoraldinho]

I have IR105 with error (the finisher cant use) and i see that the two trays did not checking when the machine turn on , but the finisher and stapler work ok.

thanks

the finisher cant use is not an error.Check error codes.Probably you have a limited
function mode.

images.jpg

[jzheld]

I have IR105 with error (the finisher cant use) and i see that the two trays did not checking when the machine turn on , but the finisher and stapler work ok.

thanks

witch trays?

[copy_suhail]

witch trays?

Tray A

[jzheld]

check the connections, cable might be bad

[SCREWTAPE]

u most open finisher front door . and found small door in left side . in the case is mechanical keys u back every keys in ON mode.

What???

Are you talking the "Dip Switches".

And let's say he puts them all on!

Then what?

[SCREWTAPE]

I have IR105 with error (the finisher cant use) and i see that the two trays did not checking when the machine turn on , but the finisher and stapler work ok.

thanks

The stapler works , but the machine says "Finisher can't be used".

UMMM...

If you go into service mode do you see "SORTER"

What about error codes. Are there any in the ERR history.

[copy_suhail]

The stapler works , but the machine says "Finisher can't be used".

UMMM...

If you go into service mode do you see "SORTER"

What about error codes. Are there any in the ERR history.

No there is no error

[SCREWTAPE]

Do you see Sorter when you go into service mode.

Copier
Feeder
Sorter
Board.

[copy_suhail]

Do you see Sorter when you go into service mode.

Copier
Feeder
Sorter
Board.

Yes I do

[SCREWTAPE]

Yes I do

Which sorter do you have.

Saddle or just the finisher.

[SCREWTAPE]

There are no error codes. Is there a E713??

There are two possible causes that would display this message.
To isolate between the two possible causes, check to see if the imageRUNNER is communicating with the Finisher. This can be done through Service Mode>Copier>Display>and check to see that IC106 & IC125 both display a Version Number.
1st Cause:
If a Version Number is PRESENT, check to see that Bit 2 on SW971 is switched to "ON" position.

2nd Cause:
If a Version Number is NOT PRESENT, check to see if 5 volts is present at J101 - Pin 3, on the Finisher Controller. The missing 5 volts will cause no communication and generate the message.
To Troubleshoot for the missing 5 volts:
Check for 5 volts at J714 - Pin 7, of the Fuse PCB. If the 5 volts is missing, check J711 - Pin 1, of the Fuse PCB for 5 volts. If 5 volts is present at J711 - Pin 1, replace the Fuse PCB, if missing, replace the Finisher Power Supply.

[copy_suhail]

There are no error codes. Is there a E713??

There are two possible causes that would display this message.
To isolate between the two possible causes, check to see if the imageRUNNER is communicating with the Finisher. This can be done through Service Mode>Copier>Display>and check to see that IC106 & IC125 both display a Version Number.
1st Cause:
If a Version Number is PRESENT, check to see that Bit 2 on SW971 is switched to "ON" position.

2nd Cause:
If a Version Number is NOT PRESENT, check to see if 5 volts is present at J101 - Pin 3, on the Finisher Controller. The missing 5 volts will cause no communication and generate the message.
To Troubleshoot for the missing 5 volts:
Check for 5 volts at J714 - Pin 7, of the Fuse PCB. If the 5 volts is missing, check J711 - Pin 1, of the Fuse PCB for 5 volts. If 5 volts is present at J711 - Pin 1, replace the Fuse PCB, if missing, replace the Finisher Power Supply.

Thank you sir I will check that today.