Canon C1 Imagepress error codes E000020-0188

[teckat]

Re: Canon C1 Imagepress error codes E000020-0485

How can I activate the patch sensor shutter from the service mode?

Take it out, and clean

Or
there is a way to check the 3 LED sensors on the image patch sensor,

Enter service mode Level 1, go to <DISPLAY>DENS> , go to second screen and it will display <PCH-LED-1>(front), <PCH-LED-2>(center), <PCH-LED-3>(rear). If any read zero, replace the image patch sensor (FM2-2494-000).

[tpant]

Re: Canon C1 Imagepress error codes E000020-0485

Check to see if the image patch sensor is reading the patches on the drum.

In service mode <Level 2>DISPLAY>DENS>, check P-SENS-P and P-SENS-S for values.
If the values are zero, replace the image patch sensor or check that the patch sensor shutter mechanism is working correctly.

Also, when was last Drum change_? & Dev change_?

How can I activate the patch sensor shutter from the service mode?

[teckat]

Re: Canon C1 Imagepress error codes E000020-0485

helppppppppp error e00020-0485

Check to see if the image patch sensor is reading the patches on the drum.

In service mode <Level 2>DISPLAY>DENS>, check P-SENS-P and P-SENS-S for values.
If the values are zero, replace the image patch sensor or check that the patch sensor shutter mechanism is working correctly.

Also, when was last Drum change_? & Dev change_?

[alexsegura27]

Re: Canon C1 Imagepress error codes E000020-0485

helppppppppp error e00020-0485

[teckat]

Re: Canon C1 Imagepress error codes E00006-0002

help

Error code E006 indicates a problem at the fixing unit connection with the front cover closed.

The screw that secures the arm release FL2-2796-000 can loosen causing poor engagement of the fixing/feeder assembly. Make certain that the screw is tight and that the arm release is not deformed.

[alexsegura27]

Re: Canon C1 Imagepress error codes E00006-0002

help

Re: Canon C1 Imagepress error codes E000020-0188

I know this is an old thread but I'm having the same problem right now, wondering if your problem got fixed and how?

[Paul 75]

Re: Canon C1 Imagepress error codes E000020-0188

I had loads of E020 errors on these machines. After numerous visits it was the patch connection from the drum unit into the connections on the main frame. Apparently they stretch and lose voltage. Try replacing the loom if all else fails !

[Alessandro72]

Re: Canon C1 Imagepress error codes E000020-0188

Hi hinnylass,
I have the same problem, you solve it?
thanks

[hinnylass]

Re: Canon C1 Imagepress error codes E000020-0188

Thank you both very much for your prompt replies. Coincidentally, have two Canon engineers here right now and I was a bit nervous about mentioning that I'd been interfering by looking online (some people are a bit funny about it). But both very grateful. One had just said exactly what you suggested before i pipped up...

Thanks again.

'Will see if this resolves issue and report back.

Re: Canon C1 Imagepress error codes E000020-0188

E0020-0188 can be caused by poor connection between Patch sensor and side driver PCB

Replace "D KIT HARNESS ASSEMBLY" Part number FM2-2615

Tom

[teckat]

Re: Canon C1 Imagepress error codes E000020-0188

Hi, there. I'm new here. But just wondered if you have an update on what this ended up being? I've been having this error code for couple of months off and on and Canon engineer has pretty much done everything he can think of (and other techs) replaced developer, patch sensor etc. But it still keeps coming up. Can do one print and then need shut down.
Baffled.

I'm without a printer off and on now since december so tearing hair out.





I'm not a tech, so please Be Kind.

have them replace the Side Driver PCB-FM2-7730-000


read here------iPRC1-Troubleshooting Procedure for E020 Error Codes.pdf

[hinnylass]

Re: Canon C1 Imagepress error codes E000020-0188

Hi, there. I'm new here. But just wondered if you have an update on what this ended up being? I've been having this error code for couple of months off and on and Canon engineer has pretty much done everything he can think of (and other techs) replaced developer, patch sensor etc. But it still keeps coming up. Can do one print and then need shut down.
Baffled.

I'm without a printer off and on now since december so tearing hair out.





I'm not a tech, so please Be Kind.

[teckat]

this one aparently has the canon engineers guessing

canon error code E000020-0188

Canon engineers guessing ????
Head-Bang.JPG

if they are guessing on this code, they belong working in a garage !!!!
u probably need a drum / dev.change- dirty sensor

Call for a CANON TRAINED TECH.

[SCREWTAPE]

If that canon tech is guessing or does not know then he must not be trained. Every canon tech would know that E20's are developer or hopper E-codes. This error has to do with yellow.
Maybe its time for a developer change.