IR5000 : How to force to copy/print ONLY face up

[Guest]

with IR5000
Can I (and How to) force to copy/print ONLY face up
Why..
cause I can run with face up copy Over 1,000 copy with out Jam
But for copy/print with face down ,It 's Jam So much (Jam Code 020F)
(I changed all new Upper Sept. claw for few day ago)

Plaee give me some idea....
Thank.....

[gensys]

with IR5000
Can I (and How to) force to copy/print ONLY face up
Why..
cause I can run with face up copy Over 1,000 copy with out Jam
But for copy/print with face down ,It 's Jam So much (Jam Code 020F)
(I changed all new Upper Sept. claw for few day ago)

Plaee give me some idea....
Thank.....

020F stationary jam at the claw sensor (PS4).
check > Motor Driver PCB

[Brian8506]

Check white inverter gate arm on rear of delivery unit for cracks. Have you changed inverter roller. How many copies on machine?

[20YRSEXP]

Brian sounds like he is in the correct area. fix the problem instead of working around it or it will just be issues later on something else. the white arm usual breaks and you cannot see it while it is in the machine. Take it out and examine it. The white arm should have a fork on the end that goes around the solenoid pin and one of the forks usually breaks.

[teckat]

with IR5000
Can I (and How to) force to copy/print ONLY face up
Why..
cause I can run with face up copy Over 1,000 copy with out Jam
But for copy/print with face down ,It 's Jam So much (Jam Code 020F)
(I changed all new Upper Sept. claw for few day ago)

Plaee give me some idea....
Thank.....

Replace the inverter rollers -

[20YRSEXP]

before replacing anything is the paper lying flat and pointing towards the exit or bending down towards the duplex unit? If it is flat and facing towards the exit then rollers and sensors probably having nothing to do with it. If it is heading down to the duplexer (the correct position) then rollers and or sensors are more likely the issue.

[mrfixit51]

Even if you were able to force printed side up delivery, you would not be able to create 2 sided copies, as the same mechanism that is used to flip the copies over for face down delivery is also part of the 2 sided copies path. For my money, you will probably find the white guide actuator, already mentioned above, is cracked...

EXTERNAL DELIVERY UPPER ASSEMBLY.pdf

[skkn]

I 'm not a tech, and don't good at english. But I would like to say
thank you for all reply , and Special thank to Brian8506 who point me to correct area

• Now I can solve my problem by Add 1 stronger spring to white inverter gate arm ,But it 's still have some jam with Jam Code 0110 ,sometime 0114

And Again, Thank for all ,who build up/Joining this forum
It 's very helpful for me.

[Brian8506]

You need to replace that arm. Its probably got a hairline crack.

[mrfixit51]

Part and part number are displayed in my file attachment in my previous posting...

[Canuck]

Replace the internal delivery roller assembly(has grey rolls on it) and the gear on the end of it. The gear has a one-way in it. Shaft gets chewed up also.Something to look at...changed many for 020F jams...usually around a million will start to act up. Same on 5570,5055 family

[andalasgt]

Replace the internal delivery roller assembly(has grey rolls on it) and the gear on the end of it. The gear has a one-way in it. Shaft gets chewed up also.Something to look at...changed many for 020F jams...usually around a million will start to act up. Same on 5570,5055 family

Can you show the pictures ? Thank you

[andalasgt]

Replace the inverter rollers -

If you don't mind, can you show me how to replace the inverter rollers. Thanks ...

[teckat]

if you don't mind, can you show me how to replace the inverter rollers. Thanks ...

fb6-5895-000=#73-fixing/feeder frame assembly
[ATTACH=CONFIG]10078[/ATTACH]

[andalasgt]

Thank you, I will learn it. ...