How to slove Canon iR C3200 print blur ?

[truongson]

I tried to clean everything, but the image printed out still blurry, nothing to be better. @Tekat maybe i have to change the brand new Transfer Belt ?

[teckat]

I tried to clean everything, but the image printed out still blurry, nothing to be better. @Tekat maybe i have to change the brand new Transfer Belt ?

Hold on> u posted two prints /
Top one shows poor Primary Transfer/ Pic below that one looks OK!!

If u think Top pic is a blurry issue/ that is a poor description //

go in service mode /print out two PG10 Prints/ and post them

[truongson]

yes, I did, tried to print PG10, but the printer does not print event PG6 or something. im using this iR C3200 without fiery.

I have 5 canon iR C3200/3220 copiers. when I changed the transfer belt from the machine working on well to this one, the image printed out still blurry and else .

[charm5496]

If you swapped ITB assemblies and you still have the same misalignment going on then the problem is pointing towards the ITB drive assembly which could have worn or dirty gears on it or your laser units need to be retimed to bring everything back into alignement.

[teckat]

u don't need a Fiery to print a PG10 Test print/ if u can't print out a PG10 or PG6>
U have other issues to be determined

[vigour]

If you swapped ITB assemblies and you still have the same misalignment going on then the problem is pointing towards the ITB drive assembly which could have worn or dirty gears on it or your laser units need to be retimed to bring everything back into alignement.

I think he is swapping the belt only, between itb units.
His picture shows an itb unit with no belt, and coloured primary transfer rollers.
His picture looks like weak image to me, not blurry.

[truongson]

u don't need a Fiery to print a PG10 Test print/ if u can't print out a PG10 or PG6>
U have other issues to be determined

yes, so sweat to use Canon iR C3200, there are a lot of troubleshot, i used to print PG10 before but right it can not print out. the colors are misalignment even i tried to clean every thing like you guide. maybe I need to clean the laser ? I afraid I can not re-seat the lasers to the old position after i take them out.

[truongson]

I think he is swapping the belt only, between itb units.
His picture shows an itb unit with no belt, and coloured primary transfer rollers.
His picture looks like weak image to me, not blurry.

I swap whole the ITB unit from other machine which's working on well to this one, not swapping the belt only @Vigour.

[teckat]

that washed out image is not a BLUR,

[vigour]

I tried to clean everything, but the image printed out still blurry, nothing to be better. @Tekat maybe i have to change the brand new Transfer Belt ?

Yes you need a new belt, and possibly primary transfer rollers.
Did you read the attachments Teckat and LindaOwen sent you.

[truongson]

yes, i did, the file @Teckat sent really usefull but i still worry about cleaning the Lasers.

[truongson]

Please to help me, why my iRc3200 didn't print PG10 or PG6 ? is there any problem with the machine if it didn't print test like this ?
Thanks

[charm5496]

do you have paper in your cassettes and registered correctly for size and type for the test page to pull from?
Choose test print hit <OK>
Choose paper source hit <OK>

push <start>

[teckat]

Please to help me, why my iRc3200 didn't print PG10 or PG6 ? is there any problem with the machine if it didn't print test like this ?
Thanks

for TEST PRINTS>
make sure that the selected tray has plain paper in it & registered in control panel

TEST1.JPGTEST.JPG

[truongson]

poor me, Some of my Canon iR 3200 have problem with cassette, I put the plain paper with letter size in cassette but the printer still says : no paper in that cassette -> I can not select paper source from cassette. I have to used MP cassette only (manual feed cassette).
Tons of troubleshot with iR C3200. Anyway everybody here so kind to help me otherwise i don't know how to do , Thanks a lot.