How to slove Canon iR C3200 print blur ?

[teckat]

call a for canon service tech to inspect your printer/

u have too many issues to deal with

[truongson]

Canon iR C3200 is not develop over here in my country that's why I can not call them for help , I have to slove them by mysel. Please help me if i'm asking the silly question about iR C3200 .

[teckat]

check your PM {Private Message}

[truongson]

Thank you @Teckat .

[truongson]

I tried to clean every thing but the color keep missing and a disalignment like picture
The Text with RED Color (100%magenta + 100%Yellow) but the yellow color out of alignment .

miss.jpgmiss color.jpg

[mrfixit51]

Yellow is not the only color misaligned in your example. It looks like a classic case of ITB wear/slippage caused by worn gears/dirty belt interior and drive roller...

[truongson]

one of my Canon iR C3220 show : E000355-0001 after I turn on . Please help me what is error ?
Thank you,

[teckat]

one of my Canon iR C3220 show : E000355-0001 after I turn on . Please help me what is error ?
Thank you,

(For details see Note #4).
Note #4-If after replacing the Counter Memory PCB an error code E355 is displayed, enter Service Mode Level 3 and perform an E355 Clear as follows:
*Additional Functions button then 28 then *Additional Functions button
*Additional Functions button then 19 then 3
COPIER>FUNCTION>CLEAR>E355-CLR
Turn OFF and then ON the equipment.

[truongson]

yes, i did, I swap the mainboard which had HDD. this machine can not boot up, so i tried to change the mainboard.

[teckat]

yes, i did, I swap the mainboard which had HDD. this machine can not boot up, so i tried to change the mainboard.

Main Board does not have a HDD on it !!!!!!!!!!!
SEE PDF>>>TP07-1.pdf

where did u get a Main pcb to swap ?? remember> u can not swap a 3200 Main with a 3220 main pcb

[teckat]

If you remove the Main Controller PCB ensure
the Counter Memory PCB has been removed and remains with the printer u removed it from .



DO NOT CHANGE TWO OR MORE BOARDS AT ANY ONE TIME. THIS CAN RESULT IN THE
EQUIPMENT ENTERING AN ERROR CODE LOOP. ONCE THIS OCCURS, YOU MUST CONTACT THE
CANON TECHNICAL SUPPORT CENTER FOR ASSISTANCE.

[truongson]

Thank you @Teckat, I will try to solve this issue .

[sniper2g8]

Re: How to slove Canon iR C3200 print blur ?

After the machine printed the 4 gradation pages... did you put them on the platen glass so the machine could scan them to adjust?
On a side note... those transfer rollers under the belt are very dirty... they need to be cleaned up...
Anyways as a first guess doesnt seem to be a second transfer roller issue, since you have the blue color missing and a disalignment issue...
Do you hear a thumping noise when the machine prints? if you do you have a broken gear on the ITB.
Seems you already tried with a different transfer unit so it should be good
Anyways, my aproach would be to clean everything, printer, laser, scanner included, then do a full gradation calibration, if that doesnt work can always try to do a DCON reset within service mode.
Good luck for you.

for color displacement goto service mode level 1 and the click on copier and then you will functions on the tab click on it. you will see clear. there reset the DC-CON and restart the machine.
Good Luck

[teckat]

Re: How to slove Canon iR C3200 print blur ?

for color displacement goto service mode level 1 and the click on copier and then you will functions on the tab click on it. you will see clear. there reset the DC-CON and restart the machine.
Good Luck

u are replying to a poster's reply from 05-15-2011

First off ---when u post anything about DCON or RCON Clear / or MN-CON u need to remind to PRINT OUT A P PRINT with service mode settings>>>COPIER > FUNCTION > MISC-P > P-PRINT
and for a MMI CLR u need to print out a USER-PRT Print for user settings

These settings need to be put back after a re-start

second off---before u clear anything because of color displacement> How about doing a VISUAL MAINTENANCE INSPECTION CHECK

color displacement
1-INSPECT INTERIOR AREAS
2-CHECK OPERATIONS
3-TEST PRINTS
4-CLEAN UNIT
5-TEST
6-ADJUSTMENTS
7-TEST

[jamesgraves]

Re: How to slove Canon iR C3200 print blur ?

I want to do a dcon clear on my canon imagerunner c3220. When I do a p-print it does not show the dcon settings. Can someone help me.