you need the iR3200 Firmware/ + the Canon Service Support Tool + a new Hard Drive
your best bet is to contact a Canon Authorized Dealer for a Canon trained tech.
-
Guest repliedRe: CLC 3200 error codes
Hi Teckat !
Unfortunately, disk scan did not help. Could you describe to me step by step how to do a firmware reload?What does this need? Please help.
Best Regards Rafael
Leave a comment:
-
Re: CLC 3200 error codes
E602-0003 - The data address registered on the HD is not consistent with the data.
Possible Cause: Write-abort error on HD sector-
Power off printer, then follow below
Hold down # 1&9 key and power ON the machine.
Keep holding down 1&9 until a white “flashing box” appears on the LCD display.
A function similar to Scan disk will be performed, which will take up to 20 minutes.
***************
if this fails u need to replace the HDD/ and reload 3200 Printer firmware with the Canon SST best bet would be to call for a Canon Trained tech-Leave a comment:
-
Guest repliedRe: CLC 3200 error codes
Hi I would like to know what these error code mean? The machine is CLC3200.
E602-0003
Please help me. RafaelLeave a comment:
-
Re: CLC 3200 error codes
thanks>good find,
like I said, customer damage 70% of the time> they think it's a toner cartridge
u should use the plastic sleeve to remove a Drum> I keep a set of four at each customerLeave a comment:
-
Re: CLC 3200 error codes
Thank you very much for all your help. There's a broken tab on my black drum unit that I didn't noticed
Thank you again!!! 
Leave a comment:
-
Re: CLC 3200 error codes
May 22, 2003
Product : imageRUNNER C3200 Title : E020 Error Code Problem :
E020 with sub code of 01B0, 02B0, 03B0, 04B0.
Solution :
If the drum units have been removed repeatedly without the drum guide service tool it's possible to break one or both tabs (see picture below).These tabs open the toner hopper when the drum unit is slid in, and if they are broken, toner will not be fed into the drum unit.
NOTE: The unit may work for a while until the developer to toner ratio drops enough to cause an error.
I have seen this broken tab issue many times / mostly caused by customers/ and the error was xxBO
An old Drum will pop xxB0 also>
E020_5.jpg
Leave a comment:
-
-
Re: CLC 3200 error codes
E732 code is a Reader communication error.
If the Reader is disconnected from the Printer a E732 code will result. Once the Reader is disconnected the logic on the MAIN-Controller is changed to a "0". The copier is now set up to be a Printer only, and will not recognize the Reader.
To correct this, you must enter service mode, COPIER>OPTION>BODY>W/SCNR and set that to "1". Then you must turn the copier off, then on.
E020 with sub code of 01B0, 02B0, 03B0, 04B0.
If the drum units have been removed repeatedly without the drum guide service tool it's possible to break one or both tabs (see picture below).These tabs open the toner hopper when the drum unit is slid in, and if they are broken, toner will not be fed into the drum unit.
NOTE: The unit may work for a while until the developer to toner ratio drops enough to cause an error.
E020_5.jpgLeave a comment:
-
Re: CLC 3200 error codes
From the Service Manual:
The 732 error: There is a reader communication error.Leave a comment:
-
CLC 3200 error codes
Hi I would like to know what these error codes mean? The machine is CLC3200.
E000732-0001
E000020-04b0
This codes sometimes appear on the machine. What I usually do is just turn the machine off then on it again. But I don't want to do that anymore for the rest of my life...
I want to know what causes this problem so that I can give solutions to this and won't appear on the machine anymore. Thank you very much.
Leave a comment: