Cannon IRC 3200 copying with yellow mask

[Guest]

Hi All,
I have a Canon IRC 3200 that prints a yellow mask when I print in color. I placed a balnk paper to see what would happen in colour mode but all i get is a yellow color printed out. If I print in balck and white the paper comes out fine. I tried swapping out the toner and drum unit for the yellow section but i still have the same results. Pleas e let me know what else i can try.

[Caldo]

Re: Cannon IRC 3200 copying with yellow mask

Are you using geniune manufactured consumables? cos if not it might contribute to the problem.

[teckat]

Re: Cannon IRC 3200 copying with yellow mask

Hi All,
I have a Canon IRC 3200 that prints a yellow mask when I print in color. I placed a balnk paper to see what would happen in colour mode but all i get is a yellow color printed out. If I print in balck and white the paper comes out fine. I tried swapping out the toner and drum unit for the yellow section but i still have the same results. Pleas e let me know what else i can try.

Turn off PASCAL in service mode. Run CCD AUTO ADJ. Turn PASCAL back on. Exit service mode and complete a FULL Autogradation.

u copy off the glass with a blank sheet> hit the print key and background is covered in yellow ?

what happens of full color network prints ????
post a copy of your issue/

Check to see if the Thrust Pin (FF6-2099-000 # 31) and Compression Spring (FS7-2826-000 #35) are making good contact with the Drum Grounding Plate.The spring can shift causing poor contact between the Drum Unit and Drum Unit Cover assembly.
This can happen with any color.
iR3200 Bias Door clip.jpg

[Progman]

Re: Cannon IRC 3200 copying with yellow mask

All of the consumables are geniune manufactured. I would check the drum section and let you know my findings.

I managed to get hold of a test sheet and this is the end result when i tried to make a copy from the scanner.

[teckat]

Re: Cannon IRC 3200 copying with yellow mask

All of the consumables are geniune manufactured. I would check the drum section and let you know my findings.

I managed to get hold of a test sheet and this is the end result when i tried to make a copy from the scanner.

Your DDI-S PCB or cable could be the problem.
that is the top board /where the interface cable goes into
check cable EXTERIOR connection position
DDI-S.JPG

The part number for the DDI-S PCB is FG3-3136-000.

[Progman]

Re: Cannon IRC 3200 copying with yellow mask

Thank you ver much Teckcat your advice worked

"Turn off PASCAL in service mode. Run CCD AUTO ADJ. Turn PASCAL back on. Exit service mode and complete a FULL Autogradation."

I only have one issue now my 11 X 7 prints get stuck in the fixing feeder unit. I tried another unit i had from another printer but still get the same problems.

Any ideas what I can look at to solve this?

[teckat]

Re: Cannon IRC 3200 copying with yellow mask

Thank you ver much Teckcat your advice worked

"Turn off PASCAL in service mode. Run CCD AUTO ADJ. Turn PASCAL back on. Exit service mode and complete a FULL Autogradation."

I only have one issue now my 11 X 7 prints get stuck in the fixing feeder unit. I tried another unit i had from another printer but still get the same problems.

Any ideas what I can look at to solve this?

is this from one one tray location ?? what is jam code ??
remove cassette tray/ take out paper/ shake/
turn cassette upside down-look to see if white gear falls out/
if so your paper width will not be recognized by sensor-

make sure your 11x17 cassette is reading for that size on display panel

[Progman]

Re: Cannon IRC 3200 copying with yellow mask

is this from one one tray location ?? what is jam code ??
remove cassette tray/ take out paper/ shake/
turn cassette upside down-look to see if white gear falls out/
if so your paper width will not be recognized by sensor-

make sure your 11x17 cassette is reading for that size on display panel

Thsnks for all the help, I got the paper to work fine.

[teckat]

Re: Cannon IRC 3200 copying with yellow mask

Thsnks for all the help, I got the paper to work fine.

Thanks, the SOLUTION WAS

[Progman]

Re: Cannon IRC 3200 copying with yellow mask

Thanks, the SOLUTION WAS

The White gear was not in place got it fixed and now there are no more paper Jams.

[teckat]

Re: Cannon IRC 3200 copying with yellow mask

The White gear was not in place got it fixed and now there are no more paper Jams.

Thumbs up.jpg


good, don't forget to look at the underside of the cassette where that post is located, inspect for crack, if u see one, the post will eventually break off, Canon has updated material,so they say- there is a fix with a metal stud, but who has time to follow Canon's useless instructions-
they break from customer changing paper size with full load of paper dropped in/ instead of adjusting slide > before paper is dropped in-