Problem in high temperature ir 5000

[bluesky2000]

I have a problem in a heater in this part

PICT1341.jpg


Where the temperature rises to a high degree

Is it possible to minimize the temperature to a level not affect the operation of the device

What is the way to change the temperature?

[zoraldinho]

Re: Problem in high temperature ir 5000

Are you a tech?

[bluesky2000]

Re: Problem in high temperature ir 5000

I have some information in this area

[CT Copier Repair]

Re: Problem in high temperature ir 5000

replace the thermistors
Copier 101

[zoraldinho]

Re: Problem in high temperature ir 5000

Don't. Call canon tech.

[teckat]

Re: Problem in high temperature ir 5000

I have a problem in a heater in this part

[ATTACH=CONFIG]11997[/ATTACH]


Where the temperature rises to a high degree

Is it possible to minimize the temperature to a level not affect the operation of the device

What is the way to change the temperature?

if u had a temperature issue / u would receive an ERROR CODE
or a "Suspended" message on control panel

Magneto.jpg call for a trained CANON Tech


Temperature Control

The machine uses the following methods to control the fixing temperature:
Description> State

NormalDescription> State

Setting in service mode

[bluesky2000]

Re: Problem in high temperature ir 5000

replace the thermistors
Copier 101

can u show me wheres is ?

Because I do not know the labels section in the device because they different from country to country

Can you put a picture for this section

Thanks for the help

[bluesky2000]

Re: Problem in high temperature ir 5000

if u had a temperature issue / u would receive an ERROR CODE
or a "Suspended" message on control panel

there is no error code or any thing in screen

look my problem is :

When printing large quantities of paper
When the paper out adjacent to each other and the paper will be very hot

This is the problem I thought that there is a way to reduce the temperature

[zoraldinho]

Re: Problem in high temperature ir 5000

that's the way it is

[Desert Rat]

Re: Problem in high temperature ir 5000

If you are not a decent tech, this machine will eat your lunch. You may be having a problem with
the cooling fan that is in the front. Clean all the filters and make sure the fan in front is working.
Otherwise the heat will build up inside the machine and harden the toner in the cleaning unit.
Then the gears on the front of the drum unit will strip. Then it will drop used toner on the transport and leave gray
spots on both sides of the copy.

Good luck

DR

[teckat]

Re: Problem in high temperature ir 5000

there is no error code or any thing in screen

look my problem is :

When printing large quantities of paper
When the paper out adjacent to each other and the paper will be very hot

This is the problem I thought that there is a way to reduce the temperature

and my problem is that u are not a tech/
I posted some SERVICE MODE adjustments

Setting in service mode

[9] Wait time reduction mode- to reduce print time; for iR5000, 4 min or less; for iR6000, 1 min or less.
[10] Priority on fixing mode-
[11] Priority on productivity mode-
[12] Thick paper mode (120/230-V model only)-
[13] Special paper mode -

COPIER>OPTION>BODY>FIX-TEMP
Use it to select down sequence mode.
0: OFF, 12: priority on productivity while controlling down
sequence temperature to

CHECK
Heat discharge fan (FM3)
Exhaust (lower rear)

[bluesky2000]

Re: Problem in high temperature ir 5000

thanks all very much


I will work with your advice

and i Will tell you about the result

thanks

[bluesky2000]

Re: Problem in high temperature ir 5000

thanks so much it working very good

[Desert Rat]

Re: Problem in high temperature ir 5000

Bluesky2000,
It is customary to post what you did to solve the problem. That way there is a record of the problem
and the solution to the problem. This way everyone will benifit from the efforts put into your problem.
Someone else may have a similar problem someday and the solution will be available. Teamwork will
benifit everyone.
So please post what you did to solve the problem.

Thanks

DR

[teckat]

Re: Problem in high temperature ir 5000

thanks so much it working very good

please post your findings- and the solution