Can you Help me about 4570 with SST 4.52 ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • SYAFIQ
    Junior Member
    • Aug 2011
    • 5
    #1

    Can you Help me about 4570 with SST 4.52 ?

    Hello every body! I have a canon ir 4570 and SST 4.52, (ping -t is ok use cross cable) but I can't connect/detect with SST v.4.52 .
    Can you help me about this problem?
    Thanks, I am sorry about my english.
    Last edited by SYAFIQ; 10-02-2011, 06:59 AM.
    Tags: 4570, canon, connect, connections, english, every, help, nec, ping, sst
    • zoraldinho
      teacher-guide-expert-guru

      Site Contributor
      2,500+ Posts
      • Mar 2008
      • 4999
      #2
      Re: Can you Help me about 4570 with SST 4.52 ?

      -Normal Mode (download mode B)

      turn on the main power while holding down 1+7; then, make the following selections in service mode:
      COPIER>FUNCTION>SYSTEM>DOWNLOAD
      -Safe Mode(download mode A)

      turn on the main power while holding down 2+8

      Capture_011.jpg

      Installing the System Software

      The system software that has been downloaded by the SST (version 3.01 or later) is saved in the temporary storage
      area of the HDD. You must then turn off and then on the main power switch so that the system software will be
      written to the system area, boot ROM, and flash ROM when the machine starts up. When you turn off and then on
      the main power switch for a second time, the machine will start up using the new version of the system software.

      [Registering the System Software]
      1) Start up the PC.
      2) Set the system CD in the PC.
      3) Start up the SST.　　
      4) Click [Register System Software]
      5) Select the drive in which you have set the System CD, and click [SEARCH].
      6) The list of system software found on the System CD appears. Remove the check from the folders and software
      you will not need; then, click [REGISTER].
      7) When the result of registration is indicated, click [OK].

      Making Connections

      [Procedure]

      1) Start up the PC.
      2) Check the network settings of the PC.
      - At the command prompt, type 'IPCONFIG', and press the Return key.
      - Check to see that the network settings are as follows:
      IP address: 172.16.1.160
      subnet mask: 255.255.255.0
      default gateway: any
      3) Check to see that the Execute/Memory lamp on the control panel is off, and turn off the main power switch
      (iR4570/3570, 2870/2270 Series).
      3-1) Hold down the power switch on the control panel for 3 sec or more.
      3-2) Follow the instructions indicated on the control panel so that the main power switch may be turned off.
      3-3) Turn off the main power switch.
      4) Connect the PC to the machine using a cross cable (iR4570/3570, 2870/2270 Series).
      5) Start up the machine to suit the download mode you will be using (iR4570/3570, 2870/2270 Series).
      - Normal Mode
      Turn on the main power switch while holding down 1+7.
      When the machine has started up, make the following selections: COPIER > FUNCTION > SYSTEM >
      DOWNLOAD.
      - Safe Mode
      Turn on the main power switch while holding down 2+8.
      6) Start up the Service Support Tool.
      7) Select the model of the machine to connect (iR2270/3570).
      8) Click [START].
      Capture_012.jpg
      Capture_013.jpg

      Capture_014.jpg
      If it ain't broke, don't fix it
      A picture is worth a thousand words

        Comment

        • SYAFIQ
          Junior Member
          • Aug 2011
          • 5
          #3
          Re: Can you Help me about 4570 with SST 4.52 ?

          Originally posted by zoraldinho
          -Normal Mode (download mode B)

          turn on the main power while holding down 1+7; then, make the following selections in service mode:
          COPIER>FUNCTION>SYSTEM>DOWNLOAD
          -Safe Mode(download mode A)

          turn on the main power while holding down 2+8

          [ATTACH=CONFIG]12080[/ATTACH]

          Installing the System Software

          The system software that has been downloaded by the SST (version 3.01 or later) is saved in the temporary storage
          area of the HDD. You must then turn off and then on the main power switch so that the system software will be
          written to the system area, boot ROM, and flash ROM when the machine starts up. When you turn off and then on
          the main power switch for a second time, the machine will start up using the new version of the system software.

          [Registering the System Software]
          1) Start up the PC.
          2) Set the system CD in the PC.
          3) Start up the SST.　　
          4) Click [Register System Software]
          5) Select the drive in which you have set the System CD, and click [SEARCH].
          6) The list of system software found on the System CD appears. Remove the check from the folders and software
          you will not need; then, click [REGISTER].
          7) When the result of registration is indicated, click [OK].

          Making Connections

          [Procedure]

          1) Start up the PC.
          2) Check the network settings of the PC.
          - At the command prompt, type 'IPCONFIG', and press the Return key.
          - Check to see that the network settings are as follows:
          IP address: 172.16.1.160
          subnet mask: 255.255.255.0
          default gateway: any
          3) Check to see that the Execute/Memory lamp on the control panel is off, and turn off the main power switch
          (iR4570/3570, 2870/2270 Series).
          3-1) Hold down the power switch on the control panel for 3 sec or more.
          3-2) Follow the instructions indicated on the control panel so that the main power switch may be turned off.
          3-3) Turn off the main power switch.
          4) Connect the PC to the machine using a cross cable (iR4570/3570, 2870/2270 Series).
          5) Start up the machine to suit the download mode you will be using (iR4570/3570, 2870/2270 Series).
          - Normal Mode
          Turn on the main power switch while holding down 1+7.
          When the machine has started up, make the following selections: COPIER > FUNCTION > SYSTEM >
          DOWNLOAD.
          - Safe Mode
          Turn on the main power switch while holding down 2+8.
          6) Start up the Service Support Tool.
          7) Select the model of the machine to connect (iR2270/3570).
          8) Click [START].
          [ATTACH=CONFIG]12081[/ATTACH]
          [ATTACH=CONFIG]12082[/ATTACH]

          [ATTACH=CONFIG]12083[/ATTACH]
          Thanks a lot for your advice.
          I will try....

            Comment

            • zoraldinho
              teacher-guide-expert-guru

              Site Contributor
              2,500+ Posts
              • Mar 2008
              • 4999
              #4
              Re: Can you Help me about 4570 with SST 4.52 ?

              Originally posted by SYAFIQ
              Thanks a lot for your advice.
              I will try....
              smile.jpg
              If it ain't broke, don't fix it
              A picture is worth a thousand words

                Comment

                • SYAFIQ
                  Junior Member
                  • Aug 2011
                  • 5
                  #5
                  Re: Can you Help me about 4570 with SST 4.52 ?

                  Originally posted by zoraldinho
                  -Normal Mode (download mode B)

                  turn on the main power while holding down 1+7; then, make the following selections in service mode:
                  COPIER>FUNCTION>SYSTEM>DOWNLOAD
                  -Safe Mode(download mode A)

                  turn on the main power while holding down 2+8

                  [ATTACH=CONFIG]12080[/ATTACH]

                  Installing the System Software

                  The system software that has been downloaded by the SST (version 3.01 or later) is saved in the temporary storage
                  area of the HDD. You must then turn off and then on the main power switch so that the system software will be
                  written to the system area, boot ROM, and flash ROM when the machine starts up. When you turn off and then on
                  the main power switch for a second time, the machine will start up using the new version of the system software.

                  [Registering the System Software]
                  1) Start up the PC.
                  2) Set the system CD in the PC.
                  3) Start up the SST.　　
                  4) Click [Register System Software]
                  5) Select the drive in which you have set the System CD, and click [SEARCH].
                  6) The list of system software found on the System CD appears. Remove the check from the folders and software
                  you will not need; then, click [REGISTER].
                  7) When the result of registration is indicated, click [OK].

                  Making Connections

                  [Procedure]

                  1) Start up the PC.
                  2) Check the network settings of the PC.
                  - At the command prompt, type 'IPCONFIG', and press the Return key.
                  - Check to see that the network settings are as follows:
                  IP address: 172.16.1.160
                  subnet mask: 255.255.255.0
                  default gateway: any
                  3) Check to see that the Execute/Memory lamp on the control panel is off, and turn off the main power switch
                  (iR4570/3570, 2870/2270 Series).
                  3-1) Hold down the power switch on the control panel for 3 sec or more.
                  3-2) Follow the instructions indicated on the control panel so that the main power switch may be turned off.
                  3-3) Turn off the main power switch.
                  4) Connect the PC to the machine using a cross cable (iR4570/3570, 2870/2270 Series).
                  5) Start up the machine to suit the download mode you will be using (iR4570/3570, 2870/2270 Series).
                  - Normal Mode
                  Turn on the main power switch while holding down 1+7.
                  When the machine has started up, make the following selections: COPIER > FUNCTION > SYSTEM >
                  DOWNLOAD.
                  - Safe Mode
                  Turn on the main power switch while holding down 2+8.
                  6) Start up the Service Support Tool.
                  7) Select the model of the machine to connect (iR2270/3570).
                  8) Click [START].
                  [ATTACH=CONFIG]12081[/ATTACH]
                  [ATTACH=CONFIG]12082[/ATTACH]

                  [ATTACH=CONFIG]12083[/ATTACH]

                  Step 1 - 6 is ok.
                  But Step 7 and 8, no choice so I can't select a model and start.

                  Thanks a alot.

                    Comment

                    • totoro
                      Senior Tech

                      Site Contributor
                      500+ Posts
                      • Apr 2008
                      • 568
                      #6
                      Re: Can you Help me about 4570 with SST 4.52 ?

                      Do you have the IR 4570 system software registered?
                      Totoro

                        Comment

                        • JustManuals
                          Field Supervisor

                          5,000+ Posts
                          • Jan 2006
                          • 9838
                          #7
                          Re: Can you Help me about 4570 with SST 4.52 ?

                          Yes, why?

                            Comment

                            • teckat
                              Field Supervisor

                              Site Contributor
                              10,000+ Posts
                              • Jan 2010
                              • 16083
                              #8
                              Re: Can you Help me about 4570 with SST 4.52 ?

                              Originally posted by SYAFIQ
                              Step 1 - 6 is ok.
                              But Step 7 and 8, no choice so I can't select a model and start.

                              Thanks a alot.


                              sst.JPG this is where the firmware should be located below
                              C:\Canon File Folder\SST System Software Folder\SST Files\iR2270_v40.03
                              your firmware needs to be registered as shown under connect/if not select REGISTER FIRMWARE>SEARCH>Highlight iR2270>
                              SST SEARCH.JPGthen elect REGISTER to add
                              **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                                Comment

                                • zoraldinho
                                  teacher-guide-expert-guru

                                  Site Contributor
                                  2,500+ Posts
                                  • Mar 2008
                                  • 4999
                                  #9
                                  Re: Can you Help me about 4570 with SST 4.52 ?

                                  Originally posted by manuals4you
                                  Yes, why?
                                  If you wont sell something,OK,but when we have technican Discussion you never help nobody,so you and your sarcasm i don't won't see again in my thread!!
                                  Last edited by zoraldinho; 10-02-2011, 08:58 PM.
                                  If it ain't broke, don't fix it
                                  A picture is worth a thousand words

                                    Comment

                                    • SYAFIQ
                                      Junior Member
                                      • Aug 2011
                                      • 5
                                      #10
                                      Re: Can you Help me about 4570 with SST 4.52 ?

                                      Originally posted by totoro
                                      Do you have the IR 4570 system software registered?
                                      No, I will backup my HD/firmware.
                                      Originally posted by manuals4you
                                      Yes, why?
                                      ????
                                      Originally posted by teckat

                                      [ATTACH=CONFIG]12094[/ATTACH] this is where the firmware should be located below
                                      C:\Canon File Folder\SST System Software Folder\SST Files\iR2270_v40.03
                                      your firmware needs to be registered as shown under connect/if not select REGISTER FIRMWARE>SEARCH>Highlight iR2270>
                                      [ATTACH=CONFIG]12095[/ATTACH]then elect REGISTER to add
                                      Thanks a lot for your share.
                                      I will try..

                                      Originally posted by zoraldinho
                                      If you wont sell something,OK,but when we have technican Discussion you never help nobody,so you and your sarcasm i don't won't see again in my thread!!
                                      I agree.......

                                        Comment

                                        Previous template Next
                                        Working...