IRC 2880I WRINKLED SHEET

[ernesto]

HI

I have problems with A3 sheet of the irc 2880i sometimes it goes out wrinkled like image attached.

someone knows the problem? the sheet goes out in the direction of the arrow (it is not jamming)
arruga papel1.jpgarruga papel.jpg

I Hope to hear from you.

thanks a lot

[nivssluck]

Re: IRC 2880I WRINKLED SHEET

HI

I have problems with A3 sheet of the irc 2880i sometimes it goes out wrinkled like image attached.

someone knows the problem? the sheet goes out in the direction of the arrow (it is not jamming)
[ATTACH=CONFIG]12575[/ATTACH][ATTACH=CONFIG]12574[/ATTACH]

I Hope to hear from you.

thanks a lot

wrinkle is always on the fuser issue...

[zoraldinho]

Re: IRC 2880I WRINKLED SHEET

Do you try to Change fixing speed? Do you have inner finisher?

[ernesto]

Re: IRC 2880I WRINKLED SHEET

Do you try to Change fixing speed? Do you have inner finisher?

Hi Zoraldinho, I don't have inner finisher, I have tried to do an A3 copy by manual feeder tray and I have selected high thick sheet and the same results. how can I change fixing speed?

[zoraldinho]

Re: IRC 2880I WRINKLED SHEET

Service Mode > Copier > Adj > FX-FL-SP and don't ask me how to get in service mode.

[charm5496]

Re: IRC 2880I WRINKLED SHEET

Service Mode > Copier > Adj > FX-FL-SP and don't ask me how to get in service mode.

How do you get into service mode???? LOL

If your paper is free of moisture and the service moded adjustments do not work you may want to look at your lower pressure roller and bushings

[fchu5959]

Re: IRC 2880I WRINKLED SHEET

[Hi,
This is a known issue; It's the decurl shaft which is not doing his job;
Either you replace the decurl assy or you replace the orange decurl shaft as well as its bearings.

cheers

[ernesto]

Re: IRC 2880I WRINKLED SHEET

[Hi,
This is a known issue; It's the decurl shaft which is not doing his job;
Either you replace the decurl assy or you replace the orange decurl shaft as well as its bearings.

cheers

Hi fchu5959 are you telling this Fu5-1559-000 bushing

Fc7-2395-000 roller paper delivery

or can you tell me the part catalog......?

[ernesto]

Re: IRC 2880I WRINKLED SHEET

Hi fchu5959 are you telling this Fu5-1559-000 bushing

Fc7-2395-000 roller paper delivery

or can you tell me the part catalog......?

HI, I am sorry but I think I don t understand it ""This is a known issue; It's the decurl shaft which is not doing his job;
Either you replace the decurl assy or you replace the orange decurl shaft as well as its bearings "

everyone knows what piece fchu5959 is telling... ?

thanks a lot

[CanonSco]

Re: IRC 2880I WRINKLED SHEET

Hi fchu5959 are you telling this Fu5-1559-000 bushing

Fc7-2395-000 roller paper delivery

or can you tell me the part catalog......?

I presume he is meaning the small diameter orange foam roller in the fuser. The bushings wear / stick and cause wrinkles. They are usually more prevalent on trail edge A3. Lubricating them normaly solves. If not - replace the roller and the bushings.

[fchu5959]

Re: IRC 2880I WRINKLED SHEET

Hi fchu5959 are you telling this Fu5-1559-000 bushing

Fc7-2395-000 roller paper delivery

or can you tell me the part catalog......?

Hi ,

Yes,these are the parts reponsible for the wrinkles on A3 trailing edge.You can always try to clean and lubricate before replacing thes parts.

cheers

[teckat]

Re: IRC 2880I WRINKLED SHEET

HI

I have problems with A3 sheet of the irc 2880i sometimes it goes out wrinkled like image attached.

someone knows the problem? the sheet goes out in the direction of the arrow (it is not jamming)
[ATTACH=CONFIG]12575[/ATTACH][ATTACH=CONFIG]12574[/ATTACH]

I Hope to hear from you.

thanks a lot

also first>>>>Do this below setting in service


Adjust Copier/Option/Body/FN-ENTMP = (-4)
Adjust Copier/Option/Body/TEMP-TBL = (-2)



also check>>

when removing the fixing drive unit (white gears) look to see if the rear alignment pin is bent / if so > it will prevent it from meshing with the lower fixing guide drive gear (brown gear). To resolve this issue the rear front fixing guide hinge plate (FL2-4393-000 / Figure 810, item 59) needs to be replaced to allow the gears to mesh correctly
( *see picture below).

20081008_0008_1.jpg

++++make sure the environment heater switch is turned ON.
++++make sure u have the latest firmware

see if Environment Heater Fuse is not blown----
see pdf---