UST= User Support Tool Information

[KhaledAlorofi]

Re: UST= User Support Tool Information

please can you send me this file iR2520_30-V0023-UST-boot.exe
khaled.kps@gmail.com

i need to update my Canon IR2520 Firmware

[scyrius]

Re: UST= User Support Tool Information

pleace can you send me this file iR2520_30-V0023-ust-boot.exe

my mail: asdcv1995@gmail.com

thanks a lot!

[mdm7266]

Re: UST= User Support Tool Information

UST Firmware is in the Models UST Firmware Folder location--

in an EXAMPLE as shown below

C:\Canon File Folder\SST System Software Folder\UST Files\CiRC1022_v61.01.01


UST Firmware Models/ & also used in their compatible Euro models

CiR LBP5280
CiR LBP5460
CiR LBP5480
iR LBP3460
iR LBP3470
iR LBP3480
iR LBP3560
iR LBP3580
CiR C1022/C1022i
CiR C1030/C1030iF
iR 1730/1740/1750
iR 2545/2535/2530/2525
LC 810/830i

hello. can you please give me a copy of ust firmware or the tools needed for my ir2545. my ir2545 cannot start/boot. cannot enter service mode. i will try to reprogram.

[teckat]

Re: UST= User Support Tool Information

hello. can you please give me a copy of ust firmware or the tools needed for my ir2545. my ir2545 cannot start/boot. cannot enter service mode. i will try to reprogram.

---

What is your scenario ( series of actions and events ) on printer

Blank display
green led on and no cycle of engine



On a fully working device, J8125 (Main Controller) measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 5v
3 - 3.2v 9 - 5v
4 - 0v 10 - 0v
5 - 0v 11 - 24v
6 - 0v

When the iR is in Blank display, green led on and no rotation or if DC Controller or Boot Rom is defective or J210 or J8112 is not connected.
J8125 measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 0v
3 - 3.3v 9 - 0v
4 - 0v 10 - 0v
5 - 0v 11 - 0v
6 - 0v



If the imageRUNNER is in the Blank Display state and listed voltage is missing on J8125, there is no way to isolate the issue to one of the listed components.

Start with cleaning and re-seating the Boot Rom, reseat connectors J210, J8112 & J8125, cut any wire ties on the related harness.

This instance of the Blank Display was resolved by replacing the Boot Rom.

Part number for the Boot Rom: FM1-B884-000

[mdm7266]

Re: UST= User Support Tool Information

---

What is your scenario ( series of actions and events ) on printer

Blank display
green led on and no cycle of engine



On a fully working device, J8125 (Main Controller) measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 5v
3 - 3.2v 9 - 5v
4 - 0v 10 - 0v
5 - 0v 11 - 24v
6 - 0v

When the iR is in Blank display, green led on and no rotation or if DC Controller or Boot Rom is defective or J210 or J8112 is not connected.
J8125 measures as follows:

Pin 1 - 0v 7 - 5v
2 - 3.2v 8 - 0v
3 - 3.3v 9 - 0v
4 - 0v 10 - 0v
5 - 0v 11 - 0v
6 - 0v



If the imageRUNNER is in the Blank Display state and listed voltage is missing on J8125, there is no way to isolate the issue to one of the listed components.

Start with cleaning and re-seating the Boot Rom, reseat connectors J210, J8112 & J8125, cut any wire ties on the related harness.

This instance of the Blank Display was resolved by replacing the Boot Rom.

Part number for the Boot Rom: FM1-B884-000

This is what happen. Ir2545
At first its intermittent error 248. at first error is cleared by power off-on. then suddenly at power on the machine cannot start-up or boot. the green light on the control panel is ON, the canon logo appears on the display. (you can hear the machine motors rotate then stop) The progress bar on the canon logo STOPS at the middle and stays there, as it hangs there.
Action taken: reseat boot rom, reseat plugs on terminals of dc con and main. still the same problem.
Do you think i need to flash or reprogram the machine?

i encounter same symptoms with a konica 7033 before and i solved it by reprogramming or re install the firmware. But this time it is a CAnon IR2545

By the way, i have also a IR 2530. are the boot rom of IR 2530 and IR 2545 the same. I have not yet open the ir2530 to compare their part numbers?

[teckat]

Re: UST= User Support Tool Information

E248-0000
Description:
EEPROM error
1.An error has occurred at power-on.
2.An error has occurred during write operation.
3.An error has occurred during read operation following write operation.

Remedy:
1.Disconnect and then connect the flexible cable(Relay PCB (PCB2)-Main Controller PCB (PCB1) 50pin).

2.Disconnect and then connect the flexible cable(CCD unit- Relay PCB (PCB2)).
3.Disconnect and then connect the power supply harness connector.
4.Replace the flexible cable.
5.Replace the CCD Unit.
6.Replace the Relay PCB (PCB2).
7.Replace the Power Supply PCB (PCB3).
8.Replace the Main Controller PCB (PCB1).