IR3570 finisher S1 issue

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • adel_nathan
    Trusted Tech
    • Jul 2011
    • 103
    #1

    [Misc] IR3570 finisher S1 issue

    hi every body
    i have a problem in photocopy machine IR3570 with finisher S1
    the problem is when paper get out from finisher , the roller dosn't get it back to hold it with three arms
    and some times paper scew
    that make a lose of some paper from staple
    and make diarrange of paper
    i change the roller and no change
    i hope you understand my bad english
    please help
    thanks
    Tags: back, bad, change, finisher, ir3570, issue, paper, roller
    • canonbundy
      Senior Tech

      500+ Posts
      • Jun 2012
      • 607
      #2
      Re: IR3570 finisher S1 issue

      Originally posted by adel_nathan
      hi every body
      i have a problem in photocopy machine IR3570 with finisher S1
      the problem is when paper get out from finisher , the roller dosn't get it back to hold it with three arms
      and some times paper scew
      that make a lose of some paper from staple
      and make diarrange of paper
      i change the roller and no change
      i hope you understand my bad english
      please help
      thanks
      Inner Finishers have a habit of frightening the heck out of Techs ie, the units are seldom included in the Machine Servicing.
      There is only a half a dozen screws in the covers to access the Transport/Delivery Rollers, shafts & bushings for lube, make sure these and the large exit rollers are cleaned properly (I use Meths)or replace them, the main reason for skewing & mis-stapling.

        Comment

        • blackcat4866
          Master Of The Obvious

          Site Contributor
          10,000+ Posts
          • Jul 2007
          • 22999
          #3
          Re: IR3570 finisher S1 issue

          The grippers on the S1 inner finisher were modified. I didn't discover it though, until I had one break the front gripper. My machine errored out E000575-000 then isolated the finisher. It did it about once every 30 days.

          Replace stack delivery slider (4F3-0243-000), operation tray (4A3-1044-000), and Op Tray Sheets (4A3-1074-000). =^..^=
          If you'd like a serious answer to your request:
          1) demonstrate that you've read the manual
          2) demonstrate that you made some attempt to fix it.
          3) if you're going to ask about jams include the jam code.
          4) if you're going to ask about an error code include the error code.
          5) You are the person onsite. Only you can make observations.

          blackcat: Master Of The Obvious =^..^=

            Comment

            • teckat
              Field Supervisor

              Site Contributor
              10,000+ Posts
              • Jan 2010
              • 16083
              #4
              Re: IR3570 finisher S1 issue

              Originally posted by adel_nathan
              hi every body
              i have a problem in photocopy machine IR3570 with finisher S1
              the problem is when paper get out from finisher , the roller dosn't get it back to hold it with three arms
              and some times paper scew
              that make a lose of some paper from staple
              and make diarrange of paper
              i change the roller and no change
              i hope you understand my bad english
              please help
              thanks
              ============================================

              As the machine ages, the following parts should be inspected.
              Quantity Part Number Description Location Comments
              1 4F3-0243-000 Stack Delivery Slider Assy Q11-1 Comes with Q11-12 / base plastic may break off
              1 4A3-1044-000 Tray, Operation Q11-5 Notch worn from wear
              2 4A3-1074-000 Sheet, Operation Tray Q11-6 goes on Q11-5
              0 4A3-1055-000 Shaft, Claw Q11-10 Be careful not to break
              0 4A3-1080-000 Sheet, Stack Delivery Guide Q11-12 Comes on Q11-1
              0 4F3-0241-000 Solenoid, Cable Q21-11 Clean
              0 Gear 64T Q21-16 Clean and lube
              0 Gear 34T Q21-17 Clean and lube
              1 4A3-1109-000 Roller, Paper Feeder Q30-3 Delivery roller
              0 4A3-1110-000 Rack, Offset Q30-4 Clean and lube
              2 4A3-1121-000 Roller, Offset Q30-14 Delivery Moon Tires
              0 4A3-1059-000 Lever, Pressure Q21-6 Breaks off and binds paper sensor causing the tray to lower all the way
              ++++++++++++
              Make sure the inlet guide to the Finisher-S1 is not bowed

              part number 4A3-1070-000

              ------------------------------------

              If the Offset Rollers               (4A3-1121-000) have become worn or damaged, the paper may not fully eject from the Finisher. If the Offset Rollers are worn or damaged they should be replaced.


              **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                Comment

                • Canuck
                  Tech Specialist

                  1,000+ Posts
                  • Nov 2007
                  • 1713
                  #5
                  Re: IR3570 finisher S1 issue

                  Is everything moving correctly mechanically? If not could be finisher board..i would pop one in quickly to check...takes 5 min. I've changed a few finisher boards on these

                    Comment

                    Previous template Next
                    Working...