Re: error code E355 - 0004
thx. please tell mi how i can reload firmware successfully. thx
error code E355 - 0004
Collapse
X
-
Re: Error code E355 - 0004_Image displays
Hey, Yeah, i have done all that, i have opened to the last board inside, reseated all cables and fibres, i have opened all pcbs, but no change. Actually , i have used this machine for 1 and half years, thats when it changed and started bringing such error codes. Anything else i havent done yet?Leave a comment:
-
Re: Error code E355 - 0004_Image displays
That should not prevent u from entering servicr mode
Are u a tech ?---have u tried removing panel connections ?
Have u unpluged connections on main pcb,s ?
What have u tried to do/ Printers don,t change language overnightLeave a comment:
-
Re: Error code E355 - 0004_Image displays
just posted some images of my control panel. and the display on the screen (Chinese language and upside down)Leave a comment:
-
Re: Error code E355 - 0004_Lost hope
Oh surely, i have failed to get into service mode.
I shall surely send u the image of my control panel in about 10hrs time.
thanks for your concern once again.Leave a comment:
-
Re: Error code E355 - 0004_Lost hope
Hey, thanks for your concerned. I am afraid my printer has no IP address. Btw, My copier is a 3in1 (copier, printer & scanner). U suggest i replace the PCB? So how much are we talking about and how many boards do i need to replace to get the machine back on track? I hear a combination of boards need to be bought together. Which ones could these be? How much will it cost me to replace these boards and where is it possible to access them at a fair price? I live in Uganda, East Africa. Thanks.
why can't u get in service mode ???????????
what are u doing to get in service mode ????
LCD Display image is reversed and upside down
Try removing & Re-fitting all the harness connections within the control panel assembly
what have u tried so far ?????????????????????
post a picture of your display panelLeave a comment:
-
Re: Error code E355 - 0004_Lost hope
Hey, thanks for your concerned. I am afraid my printer has no IP address. Btw, My copier is a 3in1 (copier, printer & scanner). U suggest i replace the PCB? So how much are we talking about and how many boards do i need to replace to get the machine back on track? I hear a combination of boards need to be bought together. Which ones could these be? How much will it cost me to replace these boards and where is it possible to access them at a fair price? I live in Uganda, East Africa. Thanks.Leave a comment:
-
Re: Error code E355 - 0004
have you tried to see your printer using RUI ???
type your printers IP Address into URL window
example below
------------------------------------------------------------------------------
LANGUAGE = Manage languages used in panel / Remote UI and font data.
Main controller PCB > replace it
re-load the firmwareLeave a comment:
-
Re:Error code E355 - 0004
Hey guys, please i would like to know anyone out there with my error experience (E355 - 0004) on Canon iR1133 UFRII LT.
I cant even get to service mode. I have tried to refit every cable or fibre.
I am almost giving up.
Please come to my rescue.
ThanksLeave a comment:
-
Re: error code E355 - 0004
--------------------------------------------------------------------------
U may need to reload firmware
but first>>>
go into service mode> COPIER > OPTION > BODY>LOCALE
before doing a CLEAR > CHECK THISLANGUAGE SETTING
Display/adj/set range 1 to 8
1: Japan, 2: North America, 3: Korea, 4: China, 5: Taiwan, 6: Europe,7: Asia, 8: Oceania
Default value 1
COPIER > OPTION > BODY
LOCALE Caution :
Since COPIER> FUNCTION> CLEAR> ALL is executed when changing the location, the setting information of user mode, service
mode, etc. is initialized.
The setting information of this item is not initialized.
Display/adj/set range 1 to 8
1: Japan, 2: North America, 3: Korea, 4: China, 5: Taiwan, 6: Europe,7: Asia, 8: Oceania
Default value 1
Related service mode COPIER> FUNCTION> CLEAR> ALL
COPIER> OPTION> BODY> SIZE-LC
SIZE-LC
Setting of paper size configurationAdj/set/operate method
1) Set the location under LOCALE.
2) Enter the setting value under SIZE-LC, and then press OK key.
3) Execute COPIER> FUNCTION> CLEAR> ALL.
4) Turn OFF/ON the main power switch.
Caution Since COPIER> FUNCTION> CLEAR> ALL is executed when
changing the location, the setting information of user mode, service
mode, etc. is initialized.
The setting information of this item is not initialized.
Display/adj/set range 1 to 4
1: AB configuration, 2: Inch configuration, 3: A configuration, 4: AB/
Inch configuration
Related service mode COPIER> FUNCTION> CLEAR> ALL
COPIER> OPTION> BODY> LOCALELeave a comment:
-
Re: error code E355 - 0004
Am afraid, no button is stuck, buddy.
Any other idea?
Am so stuck
thxLeave a comment:
-
Re: error code E355 - 0004
Counter Memory, Serial Number and Main Controller PCBs work as a set and are considered the “Soft Counter Circuit”. The Counter Memory PCB is electronically stamped with the serial number from the Serial Number PCB. Neither the Counter Memory PCB nor the Serial Number PCB can be swapped to other equipment.
The Counter Memory PCB keeps track of the total count, which cannot be erased or changed. The service counters are retained by the Main Controller. These counters can be reset manually through service mode. When the Counter Memory PCB must be replaced, after installing the new one, the new Counter Memory PCB learns the Total Count from the Main Controller. This is retained in SRAM on the Main Controller PCB and held active by means of an on board battery.
--------------------------------------------------------------------------------------------
E355 -
Cause
Mismatch of serial numbers of three items: Serial Number PCB, Main Controller/ Image Processor PCB (SRAM) and Counter Memory PCB.
Description
At power-on, a mismatch of serial numbers among the Serial Number PCB, Main Controller / Image processor PCB and Counter
Memory PCB was identified (“Prohibited Action”).
Action
1. Put back all original PCBs into the equipment! (Depends on original cause of failure)
2. Do not utilize a used Counter Memory PCB or Serial Number PCB from any other equipment. (If previously used, select
optional counters 2 through 6 (displayed in “Counter Check”) in service mode:OPTION/USER/COUNTER 2 TO 6)
If original problem was E245 or E247, Soft Counters reset to Zero.
3. Ensure connector J1023 is connected.
After “Prohibited Action” has been corrected, perform “E355 CLR”. (FUNCTION>CLEAR>E355-CLR) then cycle power off and on.
(For “70” series and later see Note #4. For imageRUNNER 1023/ 1023N/1023iF/ 2016/ 2020/ 2016i/2020i see step # 10 under
“Servicing”).
All others, Counters are retained.
Serial Number PCB is a matched board with the Counter Memory PCB and cannot be swapped with any other equipment.
On newer models from Canon (as of this writing, all “70” series and iR3530 series), to clear an E355
or E354 code, you must enter Service Mode Level 3 (see Notes #3 and #4). DO NOT ADJUST ANYTHING ELSE IN THE SERVICE MODE LEVEL! Doing so will have an adverse affect on the machine
Note #3: E354:
If, after replacing the Counter Memory PCB, an error code E354 is displayed, enter Service Mode Level 3 and perform an E354 Clear as follows:
Additional Functions button then #2/8 buttons together then Additional Functions button
Additional Functions button then #1/9 buttons together then #3 button
COPIER>FUNCTION>CLEAR>E354-CLR
Turn OFF and then ON the equipment
Note #4: E355:
If after replacing the Counter Memory PCB, an error code E355 is displayed, enter Service Mode Level 3 and perform an E355 Clear as follows:
Additional Functions button then #2/8 buttons together then Additional Functions button
Additional Functions button then #1/9 buttons together then #3 button
COPIER>FUNCTION>CLEAR>E355-CLR
Turn OFF and then ON the equipment.Leave a comment:
-
Re: error code E355 - 0004
Cool, will get back to u when i try to figure that out. thanks once againLeave a comment:
-
Re: error code E355 - 0004
Thx Teckat. yeah, its just a iR1133 just as in Canon IR1133. it does not have that interface. My buddy and i opened it to the inner board and tried to refit all fibres and other connections, but nothing changed. The fact is that i cannot access the menu/ or service code. Its in Chinese and upside down. Any other alternative? Its as if the control panel buttons are all mute. cant find any button responding or it should first be the service button (*) to respond first? I am puzzled. Please help. thanks.
Check for a stuck panel key ?Leave a comment:
Leave a comment: