clc 5151 network problem and print quality

[Rudi Hattingh]

hi
i have problem whit my printer. i set up the ip can ping it but the prnter do not want to install and print. can see it over the network.
also form usb.

and the other problem is if i print the printer prints like you need glasses .

[teckat]

Re: clc 5151 network problem and print quality

hi
i have problem whit my printer. i set up the ip can ping it but the prnter do not want to install and print. can see it over the network.
also form usb.

and the other problem is if i print the printer prints like you need glasses .

---------------------------------------------------------------
under Additional Function > System Settings > check if Print Job Restriction is turned "On" / if so turn to "0" OK!!!

Using a USB Device
Set Use USB Device to 'On' to connect a computer with the machine via the USB port.
1 Press [System Settings] [USB Settings] [Use USB Device].
2 Select [On] or [Off] press [OK].
Using a USB Host
Set Use USB Host to 'On' to connect a host device with the machine via the USB port.
1 Press [System Settings] [USB Settings] [Use USB Host].
2 Select [On] or [Off] press [OK].

Blur Prints= u need to remove ITB UNIT> INSPECT>REMOVE ITB SHEET>CLEAN> & CLEAN LARGE BLACK DRIVE ROLLER
also see

do u have a Fiery connected if so Printer needs to be set up under Control Panel Print Tab & not under the regular Add Functions>System Settings--

First your Fiery needs to be set>>
1. Enter Service mode (Additional Functions key> 2 and 8 keys together > Additional Functions key).
2. Select Copier > Option > Int-Face > IMG-CONT> "3"

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

hi
i have only usb host option. and sum how i can not put in my ip address in there is no option any more.
printer print great now if i make a copy. thank you just that i can not print form my pc. network or usb

rudi

[teckat]

Re: clc 5151 network problem and print quality

hi
i have only usb host option. and sum how i can not put in my ip address in there is no option any more.
printer print great now if i make a copy. thank you just that i can not print form my pc. network or usb

rudi

================================================== =

slow down------------

u have two options to put in your IP ADDRESS

- answer these
-do u have an external box (Fiery imagePass)Network Printer Unit H1) or a ColorPASS-GX100 connected to back of Printer
if yes -First your Fiery needs to be set>> to "3"
1. Enter Service mode (Additional Functions key> 2 and 8 keys together > Additional Functions key).
2. Select Copier > Option > Int-Face > IMG-CONT> "3"when set> u can input your settings under PRINTER TAB on top of control panel --->

if no -the Printer needs to be set >>to "0"
1. Enter Service mode (Additional Functions key> 2 and 8 keys together > Additional Functions key).
2. Select Copier > Option > Int-Face > IMG-CONT>"0"when set>u put your settings under> press > ADDITIONAL functions key> then System Settings

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

i have a fiery but if i set it to 3 my network and usb options is gone. it was on "0" set it to 3 then it give me only proxy at the network settings and at the usb the host option. no device

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

will let you know i understand wrong got the setting thanx

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

HI
if i go to printer tab it just say please wait

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

My feiry model is feiry X3IM 4VX5 AA

[teckat]

Re: clc 5151 network problem and print quality

My feiry model is feiry X3IM 4VX5 AA

===================
forget about Host Option for now
Printing from a PC via a USB cable can only be used when the Canon Multi-PDL Printer Kit is installed. //U have a H1 Fiery & not a Print Kit-------

Copier > Option > Int-Face > IMG-CONT> must be set to"3" for Fiery to Function./
also the Default Password for set up when prompted is Fiery.1 (do not use anything else)

OK !!= a Canon Inc Fiery x3im 4vx5 aa Printer Controller that's an H1 FIERY
PS (PostScript) Controller------


?- who installed this Fiery--
?- did u check the cable setup from Fiery to Printer//CHECK THE SOURCE OF THE POWER BEHIND THE PRINT SERVER MAIN UNIT AND CABLE CONNECTIONS-

Your Network settings can only be set up under the PRINTER TAB
================================================== =========================
Printer Kits for many of the newer Canon devices are LMS based. The BootROM on these devices will always end with a C.
You can check for/ or if a LMS-based Printer Kit is registered on the Canon device >
Perform the following steps:

1. Press the [Counter Check] button on the copier control panel.

2. Hit the [Device Configuration] button on the LCD screen.

3. Scroll down through all of the available pages on this Device Configuration screen. Look for either PS, PCL or UFRII.

NOTE:-Sending documents through e-mail or I-fax is available only if the Color Universal Send Kit is purchased & License is activated.
Sending documents to a file server or an inbox is also available. Sending documents via fax is available only if the optional Super G3 FAX Board is installed. Sending documents to an inbox is also available.

--If only the Color Universal Send Kitis activated, it is displayed as [Send].
Color Universal Send Kit.JPG
--If the Color Universal Send Kit is activatedand the optional Super G3 FAX Board is installed, it is displayed as [Send].
Super G3 FAX Board is installed.JPG
If only the optional Super G3 FAX Board is installed, it is displayed as [Fax].
FAX G3 only.JPG You can use the Send and Fax functions of CLC5151/CLC4040/iR C4580i/iR C4080i only if the optional
Color Image Reader-F1 or Color Image Reader-E1 is attached.
-------------------------------------------------------------------------------------------------------------------------------------

Network Scanning*
To use this function, the machine is required to be connected to a network, and the Color Network ScanGear software* installed at your computer.

this H1 install book is in English > see attachment

FOLLOW INSTRUCTIONS

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

HI
there is no ps,pcl or ufrII in the setings only imge reader f1. if i want to do the settings the printer only shows please wait....

[teckat]

Re: clc 5151 network problem and print quality

HI
there is no ps,pcl or ufrII in the setings only imge reader f1. if i want to do the settings the printer only shows please wait....

-----------

u will need to do a re-install of H1/Fiery
FOLLOW THESE RE-INSTALL INSTRUCTIONS EXACTLY AS SHOWN
=======================================
Remove H1 connections from 5151 Printer (I/F Communications cable,Cross Ethernet cable)
Remove Ethernet Straight cable from your Network wall connection
Remove H1 Power-cable from wall outlet

--next
Go into service mode, and set COPIER>OPTION>INTFACE>IMG-CONT back to "0"
Now shut down the Printer (-
When turning off the main power, be sure to go through the following in strict sequence to protect the
machine's hard disk:
[1] Hold down on the power switch on the control panel for 3 sec or more.
[2] Operate on the touch panel according to the shutdown sequence indicated so that the main power switch may be turned off.
[3] Turn off the main power switch.

---next
-Power back the 5151 Printer-
-Go back into service mode, and set> COPIER>OPTION>INTFACE> IMG-CONT back to "3"
Now get out of service mode and Power down Printer again (see above)

With 5151 Printer OFF>
---next
-Now connect the open I/F PCB Cable from H1 to 5151 Printer.
-Now connect the Cross Ethernet Cable from H1 to 5151 Printer
-Now connect the Network Cable from H1 > to your Network wall connection-
-Now plug in the H1 Power cable > from H1 to Wall Outlet
-
For the unit, there are two connected connectors for Ethernet.
The connector for the Cross Ethernet Cable is at a bottom position far from the USB port.
The connector that becomes it next to the USB port is for the Network Ethernet Cable.
Do not connect mix up connections these Cables look similar , but are a different wire configuration
HI FIERY CONNECTIONS.JPG

-Now> u POWER BACK THE 5151 Printer--/ it should come to ready,
-At the Control Panel, scroll>top arrow over & press [Printer]tab.
-Press [Printer Status/Settings].
At the Languages Setup screen, select the name of the language you want to use, and then select OK.
Wait a few minutes.
Input of password--- Fiery.1In response, the machine will automatically show the Settings menu. Be sure to at least select the following
and make the appropriate settings in the indicated order: [Server Setup], [Network Setup], and [Printer Setup].

this is where u set up everything /

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

no luck. it stay on please wait. can not go in the printer settings tab. cleaned alll card contacks and did not help. can it be that the fiery hdd is foulty.

[teckat]

Re: clc 5151 network problem and print quality

no luck. it stay on please wait. can not go in the printer settings tab. cleaned alll card contacks and did not help. can it be that the fiery hdd is foulty.

:::::;
Remove the H1 I/F Board from inside the 5151 / clean ends> & re-seat
Then remove H1 & open it up> check interior connections>
Then try the re-install as i show

[Rudi Hattingh]

Re: clc 5151 network problem and print quality

i have cleaned the all contack poins on the card and check all conections in fiery but it always say wait a moment or please wait. i ma tinking of mayby to buld all over to my irc4850i but do not like the quality of this printer it

[teckat]

Re: clc 5151 network problem and print quality

i have cleaned the all contack poins on the card and check all conections in fiery but it always say wait a moment or please wait. i ma tinking of mayby to buld all over to my irc4850i but do not like the quality of this printer it

=================
Make sure the two dip switches on H1 are in NORMAL DOWN POSITION & not in a SERVICE POSITION (UP)



-------------------------------------------------------------------------------------------------
Do u know what the difference is between cables
Ethernet-Cross cabling.jpg
CROSS OVER CABLE is most Important for establishing a connection between H1 & 5151Printer/ test it or try a replacement cable

To identify a crossover cable, compare the connectors or ends of the cable. The wire color sequence will be crossed at positions 1 and 3, and positions 2 and 6. A 'normal', 'straight-through', or 'drop' cable will have identical wiring color sequences on both ends.


Regular Patch Cable: goes from imagePass H1 to customer LAN Connection
Cross Over Cable: goes from imagePass to side of CLC5151 Machine.
There should be a link light on the imagePass when the correct cable is plugged into the RJ45 connection. Also the two digit display on the imagePass must read 00 indicating successful hardware boot.

================================================== ================================================== ====
what ver firmware is on that CLC5151/

go in service mode to print out a P PRINT


where did u get this H1 FIERY FROM ?