Requesting help from fellow techs on C650.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DadO
    Trusted Tech

    Site Contributor
    250+ Posts
    • Dec 2007
    • 401
    #1

    Requesting help from fellow techs on C650.

    Greeting all!

    I caught my self in a situation where i need to reset the fuzing/fixing unit counter of bizhub c650. I have pico fuze but it wont reset the counter. I placed it on the same place where minolta place it, that is under the fuzing unite.

    I looked for firmware on infohub but couldn't find any info on this issue only bug fixes. what firmware is it and witch hex switch.

    THX ahead
    Tags: None
    • emujo
      Field Supervisor

      2,500+ Posts
      • Jun 2009
      • 3009
      #2
      Re: Requesting help from fellow techs on C650.

      That's all there is to it...when PRCB sees new fuse it resets counter and blows fuse. You are either using the incorrect fuse, or your PRCB is damaged. You can install the PPLM mods and hide the life messages...Search this site for PPLM for info. EMujo
      If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

        Comment

        • DadO
          Trusted Tech

          Site Contributor
          250+ Posts
          • Dec 2007
          • 401
          #3
          Re: Requesting help from fellow techs on C650.

          I'm using same pico fuze (80miliamps) used for c353 series. Correct?

            Comment

            • emujo
              Field Supervisor

              2,500+ Posts
              • Jun 2009
              • 3009
              #4
              Re: Requesting help from fellow techs on C650.

              I have no idea...we put the PPLM mods in or replace the fuser, so I have never had to deal with replacing the fuses...I do remember that it is a slow-blo fuse Emujo
              If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

                Comment

                • DadO
                  Trusted Tech

                  Site Contributor
                  250+ Posts
                  • Dec 2007
                  • 401
                  #5
                  Re: Requesting help from fellow techs on C650.

                  Ok just another bad day after reseting the fuzing unite counter, machine comes in redy state and machine receive print ( or copy) job and says "print stop" under the job list. It stops there...doing nothing.

                  I saw the HDD was set to "unset" so i switched to "instaled" and same goes whit fax kit.I switched it to fax circuit board 1(on)

                  Cant do test print from service mode. The start key is red. Stabilization is no go too

                  No jams and no Error CODES! wtf?

                  help

                    Comment

                    • Copier Addict
                      Aging Tech

                      Site Contributor
                      10,000+ Posts
                      • Jul 2013
                      • 14429
                      #6
                      Re: Requesting help from fellow techs on C650.

                      Are there any P codes on the display? I don't think it will reset if there are active P codes

                        Comment

                        • emujo
                          Field Supervisor

                          2,500+ Posts
                          • Jun 2009
                          • 3009
                          #7
                          Re: Requesting help from fellow techs on C650.

                          Print stop means that some consumable has reached the end of life..Until it's reset or replaced you will not get any copy/prints. Under service mode/enhanced security there is a life stop setting, you can disable this to get a certain amount of copies out, but unless you turn on the PPLM this will only work for a short time. Emujo
                          If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

                            Comment

                            • DadO
                              Trusted Tech

                              Site Contributor
                              250+ Posts
                              • Dec 2007
                              • 401
                              #8
                              Re: Requesting help from fellow techs on C650.

                              Enhanced security did the trick. Machine is working. Problem is none of IU's have come to end of life nor did transfer belt unite.....thats whats puzzling me.

                              Thx emujo on extended help! (better then official minolta support )

                                Comment

                                • emujo
                                  Field Supervisor

                                  2,500+ Posts
                                  • Jun 2009
                                  • 3009
                                  #9
                                  Re: Requesting help from fellow techs on C650.

                                  Those guys.....

                                  Me: I have a customer with jamming from tray 3
                                  Them: Replace Main Board

                                  Me: I have a customer that has poor yellow laydown
                                  Them: Replace Main Board

                                  Me: I have a customer that certain print jobs fail
                                  Them: Update firmware, then replace Main Board

                                  Seriously, they do provide a lot of help, but they don't seem to realize just how much a Main Control Board costs...Emujo
                                  If you don't see your question answered in the forum, please don't think it's OK to PM me for a personal reply...I do not give out firmware and/or manuals.

                                    Comment

                                    • methogod
                                      Senior Tech

                                      Site Contributor
                                      500+ Posts
                                      • Dec 2008
                                      • 916
                                      #10
                                      Re: Requesting help from fellow techs on C650.

                                      they are pico slo blow fuses (green)

                                      1/16A Little Fuse


                                      Here is a link

                                      http://www.ebay.com/itm/20-pcs-Littelfuse-1-16A-62-5mA-125V-Green-Pico-Fuse-Picofuse-/151743481393

                                        Comment

                                        Previous template Next
                                        Working...