[Misc] Installed place?

[allan]

Hi there

I am trying to use status notification on a C280.
On the email it shows the IP and under "installed place" there is no info.

anybody know where this setting is?

Anybody have Savecom experiance?

[allan]

Re: Installed place?

Just throwing it back up there.

[Synthohol]

Re: Installed place?

i dont see anything about installed place.e, i get notifications all the time. out of paper, no toner, jam etc..
you can set the location under model name i guess?.
are you using some other software other than what works perfect right from the copier?
sorry if i misunderstand the question.directions below for a typical setup.


ebkit-text-stroke-width: 0px; "> 6.57 Network Settings-Detail Settings-Status Notification Setting
[Service Mode] → [Billing Setting] → [Management Function Choice]
address can be set. For SNMP TRAP function, up to five IP addresses and one IPX can be set.
bizhub C360/C280/C220 I ADJUSTMENT/SETTING > 6. UTILITY(ADMINISTRATOR
SETTINGS)
I-114
6.57.1 Register Notification Address (IP Address)
(1) Use
(2) Procedure
1. From IP address 1 to 5, select an IP address where settings are made.
2. Touch [Host Address].
3. Select [Input Host], [IPv4 Address Input] or [IPv6 Address Input] and enter a host address.
4. Touch the Clear key and enter a port number within the range of 1 to 65535 using the 10-key pad.
5. Touch [Community Name] and enter a community name.
6. Touch [Notification Item] and set the items to be notified to [ON].
7. Touch [OK] and finish the settings.
6.57.2 Register Notification Address (IPX Address)
(1) Use
(2) Procedure
1. Touch [IPX Address].
2. Touch [Network Address] or [Node Address] and enter an address.
3. Touch [Community Name] and enter a community name.
4. Touch [Notification Item] and set the items to be notified to [ON].
5. Touch [OK] and finish the settings.
6.57.3 Register Notification Address (E-mail Address)
(1) Use
(2) Procedure
1. Touch [Forward].
2. From E-mail addresses 1 to 10, select an E-mail address where settings are made.
3. Touch [Edit E-mail Address].
4. Enter an E-mail address (up to 320 one-byte characters) using the keyboard on the screen and touch [OK].
5. Touch [Notification Item] and set the items to be notified to [ON].
6. Touch [OK] and finish the settings.
6.58 Network Settings-Detail Settings-Total Counter Notification Settings
6.58.1 Notification Schedule Setting
(1) Use
(2) Procedure
1. Touch [Schedule 1] or [Schedule 2].
2. Select the reporting cycle from [Daily], [Weekly] or [Monthly].
3. When selecting [Daily] for the reporting cycle, set the Interval of day(s).
4. When selecting [Weekly] for the reporting cycle, set the Interval of week(s) and day of the Week.
5. When selecting [Monthly] for the reporting cycle, set the Interval of month(s) and date of the month.
6.58.2 Notification Address Setting
(1) Use
(2) Procedure
1. Touch [Address 1], [Address 2] or [Address 3].
2. Touch [E-mail Address Edit].
3. Enter the e-mail address (up to 320 one-byte characters) on the on-screen keyboard, and touch [OK].
4. Touch [Set Schedule].
5. Select ON/OFF for each schedule.
6.58.3 Model Name
(1) Use
bizhub C360/C280/C220 I ADJUSTMENT/SETTING > 6. UTILITY(ADMINISTRATOR
SETTINGS)
I-115
(2) Procedure
1. Touch [Model Name].
2. Enter the model name (up to 20 one-byte characters) on the on-screen keyboard, and touch [OK].
6.58.4 Send Now
(1) Use

[Kidaver]

Re: Installed place?

I had this very question myself and called tech support....took them a few days but this was the info they send me

Please go into admin mode in Pagescope, then select Network, then select IPP Setting.

Now, enter a name under Printer Location.

[allan]

Re: Installed place?

I will check that thanks.