C554e 3003 jam.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • TheBlueOrleans
    Trusted Tech

    100+ Posts
    • Aug 2012
    • 232
    #1

    C554e 3003 jam.

    Senior technician relays SSD advice to me, "replace CL8".
    Yeah. Easier said than done. Step by bloody step in the manual and I'm two hours in, getting to the clutch was harder than expected. Replacing it and I really hope this works. Going to spend the majority of my afternoon reassembling this ... I'm just going to say it because it's Friday, reassembling this motherfucker, and hoping that the clutch was the problem.


    see another thread for my unapologetic rant about swearing.
    Somewhere there is a tree working hard to produce oxygen for you to live, NOW GO APOLOGIZE TO IT!
    Tags: None
    • paulinho
      Technician
      • Jul 2010
      • 9
      #2
      Re: C554e 3003 jam.

      Originally posted by TheBlueOrleans
      Senior technician relays SSD advice to me, "replace CL8".
      Yeah. Easier said than done. Step by bloody step in the manual and I'm two hours in, getting to the clutch was harder than expected. Replacing it and I really hope this works. Going to spend the majority of my afternoon reassembling this ... I'm just going to say it because it's Friday, reassembling this motherfucker, and hoping that the clutch was the problem.


      see another thread for my unapologetic rant about swearing.

      Hi mate,

      Just wondering whether replacing CL8 fixed the issue?

      I have a brand new 554e (<400 copies) with j3003 from all trays. I checked ps3 (even swapped with duplex sensor), checked & reconnected all prcb connectors, removed paper exit assy and cleaned one-way gear, checked registration roller turning ok. No luck.

      Any feedback will be greatly appreciated.

      Cheers

        Comment

        • blackcat4866
          Master Of The Obvious

          Site Contributor
          10,000+ Posts
          • Jul 2007
          • 22997
          #3
          Re: C554e 3003 jam.

          Yes the clutch should solve it. Just watch for a pile of rust on the drive actuator on the door. I wrote this procedure for the 454e but it should guide you in the right direction. I know there's some duplication: I think it says to plug in the fuser motor three times. I'll be correcting that. =^..^=
          Attached Files
          If you'd like a serious answer to your request:
          1) demonstrate that you've read the manual
          2) demonstrate that you made some attempt to fix it.
          3) if you're going to ask about jams include the jam code.
          4) if you're going to ask about an error code include the error code.
          5) You are the person onsite. Only you can make observations.

          blackcat: Master Of The Obvious =^..^=

            Comment

            • EarthKmTech
              Step aside, noob

              1,000+ Posts
              • May 2009
              • 2139
              #4
              Re: C554e 3003 jam.

              Originally posted by blackcat4866
              Yes the clutch should solve it. Just watch for a pile of rust on the drive actuator on the door. I wrote this procedure for the 454e but it should guide you in the right direction. I know there's some duplication: I think it says to plug in the fuser motor three times. I'll be correcting that. =^..^=
              Have you noticed the fusing exit gray roller shaft on the top of the side door also starting to bind up around this meter count ? We have and now keep its bushings lubricated as soon as it starts, as it certainly doesn't help the situation. (224-554)

              Eventually if ignored the bushings end up ovaled out and paper jams result. takes 1 second to turn and check on each call, along with checking the reg rollers for tightness.

                Comment

                • tech51
                  Senior Tech

                  500+ Posts
                  • Jan 2009
                  • 846
                  #5
                  Re: C554e 3003 jam.

                  Originally posted by paulinho
                  Hi mate,

                  Just wondering whether replacing CL8 fixed the issue?

                  I have a brand new 554e (<400 copies) with j3003 from all trays. I checked ps3 (even swapped with duplex sensor), checked & reconnected all prcb connectors, removed paper exit assy and cleaned one-way gear, checked registration roller turning ok. No luck.

                  Any feedback will be greatly appreciated.

                  Cheers
                  If it is less than 400 copies I wouldn't think its the clutch. I have had a print control board cause it. Also there was a bulletin regarding the wiring to the clutch. Would be worth checking that out.

                    Comment

                    • paulinho
                      Technician
                      • Jul 2010
                      • 9
                      #6
                      Re: C554e 3003 jam.

                      Originally posted by blackcat4866
                      Yes the clutch should solve it. Just watch for a pile of rust on the drive actuator on the door. I wrote this procedure for the 454e but it should guide you in the right direction. I know there's some duplication: I think it says to plug in the fuser motor three times. I'll be correcting that. =^..^=

                      Thanks mate. It ended up being faulty PS3 & PS40 sensors, therefore all fixed after replacing the sensors.

                      Cheers

                        Comment

                        • n25an
                          Service Manager

                          Site Contributor
                          1,000+ Posts
                          • Jul 2008
                          • 1030
                          #7
                          Re: C554e 3003 jam.

                          Originally posted by blackcat4866
                          Yes the clutch should solve it. Just watch for a pile of rust on the drive actuator on the door. I wrote this procedure for the 454e but it should guide you in the right direction. I know there's some duplication: I think it says to plug in the fuser motor three times. I'll be correcting that. =^..^=
                          bless you...
                          bless you...
                          bless you man...
                          I could cry...
                          Sad To Say I Don't Have a Life
                          I do this stuff on the weekends too

                            Comment

                            • blackcat4866
                              Master Of The Obvious

                              Site Contributor
                              10,000+ Posts
                              • Jul 2007
                              • 22997
                              #8
                              Re: C554e 3003 jam.

                              Many people cry over my posts. You're in good company. =^..^=
                              If you'd like a serious answer to your request:
                              1) demonstrate that you've read the manual
                              2) demonstrate that you made some attempt to fix it.
                              3) if you're going to ask about jams include the jam code.
                              4) if you're going to ask about an error code include the error code.
                              5) You are the person onsite. Only you can make observations.

                              blackcat: Master Of The Obvious =^..^=

                                Comment

                                Previous template Next
                                Working...