Konica C220 -jams between ITB & fuser

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jonbonse
    Senior Tech

    Site Contributor
    500+ Posts
    • Jun 2009
    • 730

    #1

    Konica C220 -jams between ITB & fuser

    Hi all

    Is there a mod (such as a stick on mylar) to stick on the ITB so the paper doesn't curl up under the fuser and cause a jam?
  • D_L_P
    Self Employed

    1,000+ Posts
    • Oct 2009
    • 1196

    #2
    Re: Konica C220 -jams between ITB & fuser

    I don't know of any tech pubs relating to the area between the itb and fuser. I think there was a tech pub adding mylar to the fuser exit area. Is the plastic guide on the itb belt missing?

    Comment

    • tech51
      Senior Tech

      500+ Posts
      • Jan 2009
      • 846

      #3
      Re: Konica C220 -jams between ITB & fuser

      There isn't a plastic guide on the c220. That was introduced on the 4 range.

      Comment

      • blackcat4866
        Master Of The Obvious

        Site Contributor
        10,000+ Posts
        • Jul 2007
        • 22997

        #4
        Re: Konica C220 -jams between ITB & fuser

        Jam codes? =^..^=
        If you'd like a serious answer to your request:
        1) demonstrate that you've read the manual
        2) demonstrate that you made some attempt to fix it.
        3) if you're going to ask about jams include the jam code.
        4) if you're going to ask about an error code include the error code.
        5) You are the person onsite. Only you can make observations.

        blackcat: Master Of The Obvious =^..^=

        Comment

        • Don N.
          Trusted Tech

          250+ Posts
          • Nov 2011
          • 409

          #5
          Re: Konica C220 -jams between ITB & fuser

          Most of our c220's have one sep claw on the TB. The new TB has 3. I just had a c220 leaving paper 1/2 way exiting the fuser, next piece is curled under the fuser above the TB, BUT I think the clue is one in the verticle feed area. Jam code is 2011. It never jams from tray 1, only has 2 trays. New tires & 1-way bearings all the way around. I suspect the vert feed clutch is shot. Usually some CRC cleaner spray will fix those clutches, but after 200~300k+ they're toast. I came here tonight looking for verticle feed jamming info I remember someone saying there's a roller & pressing springs mod. Maybe that's for the 4 series??

          Comment

          • Don N.
            Trusted Tech

            250+ Posts
            • Nov 2011
            • 409

            #6
            Re: Konica C220 -jams between ITB & fuser

            Most of our c220's have one sep claw on the TB. The new TB has 3.
            I just had a c220 today leaving paper 1/2 way exiting the fuser, next piece is curled under the fuser above the TB, BUT I think the clue is one in the vertical feed area. Jam code is 2011. It never jams from tray 1, only has 2 trays. About 160k on tray 2. Put new tires & 1-way bearings on. Flushed the clutches with crc as usual. I suspect the vert feed clutch is shot. Usually some CRC cleaner spray will fix those clutches, but after 200~k+ they're toast. I came here tonight looking for vertical feed jamming info I remember someone saying there's a roller & pressing springs mod. Maybe that's for the 4 series??

            Comment

            Working...