Bizhub C652 Digital noise on prints and copies.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Zesti
    Trusted Tech

    250+ Posts
    • Jun 2009
    • 308
    #1

    [CQ] Bizhub C652 Digital noise on prints and copies.

    Looking for attention of senior Bizhub techs.
    Have that older and my favorite C652. It started creating digital noise like sequential lines and boxes on copies, prints and internal test prints. Tried all the adjustments first and all the internal tests like RAM were OK. The problem grew up over time and last print is attached.
    I tried replacing available PH unit and drive board with no good effect. I suspected the MFP board part no. A0P0-H021 found one, received, installed but no display. The engine initializes but panel is blank, no keys responding. I tried flash the machine and it seems that the USB was detected by machine on service port as engine does not initialize but no display whatsoever.
    I noticed some difference of writing on boards regarding part nos. Images attached for new and old board. Kindly shed some light on what could be wrong.Old faulty MFP board-1.jpgNew MFP Board-1.jpgFaulty image.pdfng.
    Tags: attached, board, c652, internal, prints
    • srvctec
      Former KM Senior Tech

      500+ Posts
      • Oct 2009
      • 827
      #2
      Re: Bizhub C652 Digital noise on prints and copies.

      Is the new MFP board actually new or from another machine? If the machine's display was working before the MFP board swap, then the "new" MFP board is bad or a connector isn't seated properly somewhere. Have you tried to put the original board back in to make sure the panel still works with it? Also, for the initial problem, swap out the memory board(s) to see if anything changes. I had something similar happen on a C552 and it turned out to be the MFP board.
      Started in the copier service business in the fall of 1988 and worked at the same company for 33.5 years, becoming the senior tech in 2004 but left to pursue another career on 4/29/22.

        Comment

        • EarthKmTech
          Step aside, noob

          1,000+ Posts
          • May 2009
          • 2139
          #3
          Re: Bizhub C652 Digital noise on prints and copies.

          you could try getting someone handy with a hot air soldering station to replace the soldered down ram chips on the working but image defecting mfp board. Its not actually that hard. I've long expected this to be the problem but have not tried personally as we just change whole boards.

          I just threw out a 1 foot pile of good used mfp boards for this series and others similar we don't service them anymore.

            Comment

            • Zesti
              Trusted Tech

              250+ Posts
              • Jun 2009
              • 308
              #4
              Re: Bizhub C652 Digital noise on prints and copies.

              Thanks Srvctec and Earthkmtech,
              The board I got was new as mentioned by seller. The seller said he only sell boxes no technical know how...
              The old board is still working with faulty image.
              Unfortunately I don't have another C652 to cross check the fault.

              I'm inline with advice from earthkmtech, the old board is already with me and I have to visit an electronic board geek to do the same.

              Any advise regarding marking of boards I posted.

                Comment

                • EarthKmTech
                  Step aside, noob

                  1,000+ Posts
                  • May 2009
                  • 2139
                  #5
                  Re: Bizhub C652 Digital noise on prints and copies.

                  both boards are a0p0h021 mfp boards it must be defective. did you remember to plug in the control panel in and are there led's lit up on the board (indicating it is powered)?

                    Comment

                    • Zesti
                      Trusted Tech

                      250+ Posts
                      • Jun 2009
                      • 308
                      #6
                      Re: Bizhub C652 Digital noise on prints and copies.

                      Originally posted by EarthKmTech
                      both boards are a0p0h021 mfp boards it must be defective. did you remember to plug in the control panel in and are there led's lit up on the board (indicating it is powered)?
                      Yup the panel connector is well checked. Good point about LED's on of board. The non working board has few LEDs not glowing while these glow on old board. Any info about LEDs on mfp board, couldn't find in sm.

                      Sent from my RHYTHM RX60 using Tapatalk

                        Comment

                        Previous template Next
                        Working...