Bizhub C224e not detecting firmware

[Ari007]

Re: Bizhub C224e not detecting firmware

I tried booting it with the firmware USB port cover open. It doesn't starts to boot. After I let go the lid to it's original position, machine starts to boot 🤔

[rrrohan]

Re: Bizhub C224e not detecting firmware

Have to try it... I have a DF-624..

if only problem with old SSD was its not waking from sleep id be tempted to put old SSD back in and just disable sleep mode

[Ari007]

Re: Bizhub C224e not detecting firmware

This happened to me on a C364e.
Detaching the Job Separator, strangely the firmware has started! If you have options like finisher, DF and more, try removing them temporarily


@rrrohan, a curiosity. Where can I find SSD firmware V6.05? What filter should I use on infohub?

Have to try it... I have a DF-624..

[Ari007]

Re: Bizhub C224e not detecting firmware

have you applied the SSD V6.05 firmware?

SSD came with 6.05m firmware

[rrrohan]

Re: Bizhub C224e not detecting firmware

This happened to me on a C364e.
Detaching the Job Separator, strangely the firmware has started! If you have options like finisher, DF and more, try removing them temporarily


@rrrohan, a curiosity. Where can I find SSD firmware V6.05? What filter should I use on infohub?

well im not sure they might of intergrated it into the main firmware by now but ill link it to you in half a day when im back at work

[Bix]

Re: Bizhub C224e not detecting firmware

This happened to me on a C364e.
Detaching the Job Separator, strangely the firmware has started! If you have options like finisher, DF and more, try removing them temporarily


@rrrohan, a curiosity. Where can I find SSD firmware V6.05? What filter should I use on infohub?

[rrrohan]

Re: Bizhub C224e not detecting firmware

have you applied the SSD V6.05 firmware?

[Ari007]

Re: Bizhub C224e not detecting firmware

When I started it in the morning with the new RAM installed, it started to boot then restarted and then stuck at 4 bars..

[Ari007]

Re: Bizhub C224e not detecting firmware

Turn on machine while holding op panel's Power button, wait for a beep. Do self diagnostic and look for any NG results, probably if it fails at second pillar(fin) some memory tests will fail.

Tried this but two bars.. installed new RAM... Same results

[Ari007]

Re: Bizhub C224e not detecting firmware

Yea the reset tool comes to mind.
Should boot into diagnostic mode to test RAM.

I've tried reset tool but not detecting.

[Ari007]

Re: Bizhub C224e not detecting firmware

SSD Brand New or Pulled from another machine???[emoji848]

Sent from my SM-N950U1 using Tapatalk

SSD is brand new..

[Ari007]

Re: Bizhub C224e not detecting firmware

How did you enter CE mode to disable the HDD if the machine wont boot?

Disabled when the machine was running fine... a week ago

[copyman]

Re: Bizhub C224e not detecting firmware

Agree use the firmware reset tool.

Also try booting up with service USB port open but no flash drive in it. It should boot up so you can get into service mode etc

[allan]

Re: Bizhub C224e not detecting firmware

Yea the reset tool comes to mind.
Should boot into diagnostic mode to test RAM.

[qbert69]

Re: Bizhub C224e not detecting firmware

I have a bizhub c224e, with low copy/print. The machine was running fine but had some deep sleep issues. Now, if the main sw is turned on it does the full warmup procedure(can tell from the sound) and gets stuck at two fins. If firmware is inserted from service port first it stays off and if main switch is turned on/off it again gets stuck at two fins.

*SSD replaced
*All the sensors are working
*HDD is disconnected and disabled from service mode.

Please help.

SSD Brand New or Pulled from another machine???[emoji848]

Sent from my SM-N950U1 using Tapatalk