MINOLT BIZHUB C360 alignment problem on color prints

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tecnomarco
    Trusted Tech

    100+ Posts
    • Jul 2011
    • 213
    #1

    MINOLT BIZHUB C360 alignment problem on color prints

    hello to all I have a problem on prints and color copies of yellow color alignment .... it creates a double line for me a "line position problem ... in assistance mode how can I correct this, can you tell me the simulation to do? in assistance mode..thank you I have attached some prints
    Attached Files
    Tags: color, line, mode, prints
    • davidj7
      Service Manager

      Site Contributor
      1,000+ Posts
      • Jan 2009
      • 1107
      #2
      Re: MINOLT BIZHUB C360 alignment problem on color prints

      are you using compatible drums?

      did it happen just all of a sudden or after drums were changed?


      in service mode ->stabilization should fix it
      a machine is only as good as your tech : source:screwtape ; the scary one

        Comment

        • tecnomarco
          Trusted Tech

          100+ Posts
          • Jul 2011
          • 213
          #3
          Re: MINOLT BIZHUB C360 alignment problem on color prints

          Thank's David ...yes I use drum compatible but I have change only drum black, not colour..

            Comment

            • tecnomarco
              Trusted Tech

              100+ Posts
              • Jul 2011
              • 213
              #4
              Re: MINOLT BIZHUB C360 alignment problem on color prints

              they are complete compatible drums not regenerated by me

                Comment

                • tsbservice
                  Field tech

                  Site Contributor
                  5,000+ Posts
                  • May 2007
                  • 7975
                  #5
                  Re: MINOLT BIZHUB C360 alignment problem on color prints

                  Originally posted by tecnomarco
                  Thank's David ...yes I use drum compatible but I have change only drum black, not colour..
                  Color registration is based on K(black) so...
                  Remove ITB and clean IDC sensors (x2) then as suggested make stabilization.
                  By the way this compatible drum does it have new chip?
                  A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
                  Blessed are they who can laugh at themselves, for they shall never cease to be amused.

                    Comment

                    • tecnomarco
                      Trusted Tech

                      100+ Posts
                      • Jul 2011
                      • 213
                      #6
                      Re: MINOLT BIZHUB C360 alignment problem on color prints

                      Originally posted by tsbservice
                      Color registration is based on K(black) so...
                      Remove ITB and clean IDC sensors (x2) then as suggested make stabilization.
                      By the way this compatible drum does it have new chip?
                      Thank's I will do as you say

                        Comment

                        • occus
                          Trusted Tech

                          250+ Posts
                          • Jul 2013
                          • 331
                          #7
                          Re: MINOLT BIZHUB C360 alignment problem on color prints

                          I see a little skew on yellow...
                          Clean IDC Sensors, go first in machine>print head skew adjustment>print head skew adjustment reset 2x and make the stabilization and gradations adjumstments.

                          I think it's important to have a black drum in good conditions.

                            Comment

                            • tecnomarco
                              Trusted Tech

                              100+ Posts
                              • Jul 2011
                              • 213
                              #8
                              Re: MINOLT BIZHUB C360 alignment problem on color prints

                              Originally posted by occus
                              I see a little skew on yellow...
                              Clean IDC Sensors, go first in machine>print head skew adjustment>print head skew adjustment reset 2x and make the stabilization and gradations adjumstments.

                              I think it's important to have a black drum in good conditions.
                              Thank's occus i change the new drum black but can you explain to me this simulation....machine-print head skew adiustment....ecc

                                Comment

                                Previous template Next
                                Working...