Bizhub 451 P-14 Error

[habik]

Re: Bizhub 451 P-14 Error

in service mode...where you do Skew Adjustment

[medmouncef]

Re: Bizhub 451 P-14 Error

in service mode...where you do Skew Adjustment

Thanks. I'll test it on my machine.

[mdtrinh]

Re: Bizhub 451 P-14 Error

P-14 means there is a skew problem. My experience is that it mostly deals with the black IU. 1st pull out the black IU and reseat it. But before locking the black IU hold it in place with your hand then lock it. Sometimes it doesn't sit right. The other alternative is if it doesn't work try replacing the black IU.

PS - as a precaution reseat all IU's

Hope this helps!

Thanks!
We have to replace the black IU to solve the problem.
Bad black IU unit also show up same problem in different machine.

[habik]

Re: Bizhub 451 P-14 Error

Thanks!
We have to replace the black IU to solve the problem.
Bad black IU unit also show up same problem in different machine.

Nice one.

I have changed Bk IU and ITB and no difference. Cleaning skew mechanism apparently helps as someone already mentioned here already...I did not need to do that...my fix was new values in Skew.

Thanks for the info on how you have fixed it!

[habik]

Re: Bizhub 451 P-14 Error

Just Flashed one of our machines with GSR-R6 and we shall see, if the P-14 comes back. I had it on Manual Skew Adjust with figures

C-480
M-480
Y-193

Now with the Firmware I did:

Skew Adjust Reset + Initialize and Image Stabilise

Flashed with GSR-R6

Skew Adjust Reset + Initialize and Image Stabilise

P-14 went away

Magic will see for how long

Thanks for watching Have a nice weekend folks.

[medmouncef]

Re: Bizhub 451 P-14 Error

Just Flashed one of our machines with GSR-R6 and we shall see, if the P-14 comes back. I had it on Manual Skew Adjust with figures

C-480
M-480
Y-193

Now with the Firmware I did:

Skew Adjust Reset + Initialize and Image Stabilise

Flashed with GSR-R6

Skew Adjust Reset + Initialize and Image Stabilise

P-14 went away

Magic will see for how long

Thanks for watching Have a nice weekend folks.

Hi.

I have searched the internet nut I do not find this new version GSR-R6. Please Can you send it to me.
Thank you very much.

[dirtyfingers]

Re: Bizhub 451 P-14 Error

The GSR-R6 isn't the magic firmware to look for.

ALL the Gxx-R6 firmware support the P-14 fix (Threshold changed)

On older firmware (J8/R5 etc )
If the skew correction cannot be done ...then the skew control motors go back to home position.

ON R6 firmware the skew control stays at maximum adjustment if outside the range.

from notes
5. When the alert code P-14 is detected after PH and IU are changed, color registration error or skewed image may occur because the skew correction control is not performed.

[Erick Nyaks]

Re: Bizhub 451 P-14 Error:

Hi I am having constant issue with C650 (+650) right this moment and would appreciate if anyone can send me a link to the GC1-22 special firmware on the Konica site...

Many Thanks

I looked through 1.5 hrs now and could not find it.

Am also looking for the firmware for bizhub c550 to reset the same skew error any help

[habik]

Re: Bizhub 451 P-14 Error:

Am also looking for the firmware for bizhub c550 to reset the same skew error any help

Have you looked in the archive?

[JustManuals]

Re: Bizhub 451 P-14 Error

I have this firmware but it isn't free. If you're interested in buying it, email me at paul@justmanuals.com

[Synaux]

Re: Bizhub 451 P-14 Error:

Am also looking for the firmware for bizhub c550 to reset the same skew error any help

It is listed in the base firmware...not the special firmware section. Hope this helps

[Shiv]

Re: Bizhub 451 P-14 Error

pls explain it again

[Synthohol]

Re: Bizhub 451 P-14 Error

that was 4 years ago.
good luck.