Konika Minolta BizHub 163 - Error Code? M2

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

I wont give up, those 3 copies gave me hope! I am going to try what mrwho said...

[mrwho]

Re: Konika Minolta BizHub 163 - Error Code? M2

Where is developer suppost to be? in what comora?... some1 explain me that... :S ... ima canon servicier , not konika ... i tought its rest toner xD..

where is rest toner here actualy?

With the developer back on the IU, if you're getting error codes C0F32, the only thing you can try to do is to manually adjust the ATDC Gain - increase it 5 points and try to use the machine. If it errors again, increase it another 5 and try again. Keep doing this until the error disappears. If you reach the maximum value and still the error C0F32 comes up, go back to the initial value and then reduce the value by 5 at a time and keep trying until you find the sweet spot.

Things can't get much worse - unless you decide to clean up the drum with sandpaper, I guess!

[Avskrap]

Re: Konika Minolta BizHub 163 - Error Code? M2

Dude, call a tech already. If you keep this up you'll wreck the whole machine, if you haven't already... You're clearly in over your head and dumping used, vac'ed developer in it is just massively wrong on so many levels...

[Hansoon]

Re: Konika Minolta BizHub 163 - Error Code? M2

Good Lord have mercy.........

Hans

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

Where is developer suppost to be? in what comora?... some1 explain me that... :S ... ima canon servicier , not konika ... i tought its rest toner xD..

where is rest toner here actualy?

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

I removed developer from vacoom, filled it back, and copier made 3 copies !




and stoped again and gave me same error...drum made 60000,so i guess its time for new unit? ...


fail

[mrwho]

Re: Konika Minolta BizHub 163 - Error Code? M2

and now it gives me error C0F32 .. damn :S

You'll need a new developer. And a Service Manual, so you won't screw things up again.

Or, better yet, call a technician - It would already be cheaper if you did it the first time around.

[mrwho]

Re: Konika Minolta BizHub 163 - Error Code? M2

Since no1 told me what ''developer'' is,now i learned, i used vacoom to remove it,and now i am doomed -.-'

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

and now it gives me error C0F32 .. damn :S

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

Since no1 told me what ''developer'' is,now i learned, i used vacoom to remove it,and now i am doomed -.-'

That 40k counter is not for the toner - the "supplies" part is meant for the Drum, Developer, Cleaning Blade, Charge Corona and Filter, all of those inside the Imaging Unit. There's actually no harm on reseting those, as long as you keep some record of when was the last time those were changed. The only one that shouldn't be run without actualy replacing the developer is the ATDC auto adjust - and there are some precautions to be taken when doing it.

Cheers!

[mrwho]

Re: Konika Minolta BizHub 163 - Error Code? M2

So, I made mistake by deleting supplies data? :S ... Machine actualy started to work after reseting,so I guess machine is set to make 40000 with 1 toner,but it didnt reset after adding new toner,so I did it manualy in service mode...

I am not into konica minolta too much, sooo i may sound stupid..

That 40k counter is not for the toner - the "supplies" part is meant for the Drum, Developer, Cleaning Blade, Charge Corona and Filter, all of those inside the Imaging Unit. There's actually no harm on reseting those, as long as you keep some record of when was the last time those were changed. The only one that shouldn't be run without actualy replacing the developer is the ATDC auto adjust - and there are some precautions to be taken when doing it.

Cheers!

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

So, I made mistake by deleting supplies data? :S ... Machine actualy started to work after reseting,so I guess machine is set to make 40000 with 1 toner,but it didnt reset after adding new toner,so I did it manualy in service mode...

I am not into konica minolta too much, sooo i may sound stupid..

thats the only thing that should of been changed.

the IU counter shouldn't of been reset without actually changing the parts.

the drum will usually last up-to 60k before it fails but don't count on it.

[Smiley27]

Re: Konika Minolta BizHub 163 - Error Code? M2

So,how do I run it?''atdc'' and,what that is?

Be prepared for an error code very soon! If you do not run atdc setup after you clear the supplies counter ..you will get the error!

[EarthKmTech]

Re: Konika Minolta BizHub 163 - Error Code? M2

Also, should I set IU life stop mode to : continue ( its on STOP now )

thats the only thing that should of been changed.

the IU counter shouldn't of been reset without actually changing the parts.

the drum will usually last up-to 60k before it fails but don't count on it.

[minimerlin]

Re: Konika Minolta BizHub 163 - Error Code? M2

Error is cleared. Machine works now, I am suppost to replace drum since it made 40000, but drum is fine...

If I want machine to make another ''?????'' what counters do need to be clear? I already deleted ''Supplies Counter'' , but I am afraid machine will stop again if another counter reaches its limit..

So I got :

MEMORY COUNTER
TOTAL COUNTER
PM COUNTER
MAINTENANCE COUNTER
SUPPLIES COUNTER ( CLEARED )
APPLICATION COUNTER
SCAN COUNTER
MISFED COUNTER
PAPER SIZE COUNTER

Also, should I set IU life stop mode to : continue ( its on STOP now )


Also,give me a clue what exactly ''developer'' is? drum?

Be prepared for an error code very soon! If you do not run atdc setup after you clear the supplies counter ..you will get the error!