Laserman06...the c350 is acting up again. All seemed fine then a message regarding the right door not being closed (when it was) came up. The office folks put a little pressure on the door which worked just fine and allowed the printer to go about its business. Then this code popped up C-0096. I know that it is a transfer belt issue. Do you have any ideas as to where to look?? Do you have any magic up your sleeves for this one?
-
-
that's a transfer belt pressure error, probally because of the door. it's common for the rear door hook to break, it's a pretty cheap plastic.Comment
-
You hardwire that fuse on the fuser unit Laserman? the original is a little one that looks like a resistor right?Comment
-
That is correct the original fuse is a pico style fuse, located in the connector wiring harness. I just snip it off, strip the insulation off both wires about an inch. I used to solder the wires on, but it is much easier to wrap the wires on around each end and tape them up. Completely enclose the fuse in electrical tape. I then check for continuity between the two pins that the wires lead to. Should have around 5.3 milliohms.The family that prays together, stays together!
Smile God created you and He doesn't make mistakes!
Relax, God IS in control!
Be still and know that I am God
Ps 46:10Comment
-
I have to agree with mrfixit. Sounds like the door latch, especially if the customer can push in on the door and it works. Also what you might want to check is that the transfer belt is fully seated. It is possible to push in the locking mechanisms without it being totally seated. Might be your problem.The family that prays together, stays together!
Smile God created you and He doesn't make mistakes!
Relax, God IS in control!
Be still and know that I am God
Ps 46:10Comment
-
Will this aslo work for the c353?
I am getting a warning that i need to replace the image transfer belt on my Konica c353... can i simply replace the fuse in the transfer belt unit?Comment
-
Yes, the transfer belt can be reset with a fuse.The family that prays together, stays together!
Smile God created you and He doesn't make mistakes!
Relax, God IS in control!
Be still and know that I am God
Ps 46:10Comment
-
C353... When I unscrew the 2 screws that keep the transfer belt in place and try to pull the transfer belt out, it gets stuck. It is catching on something. What am I doing wrong?Comment
-
Master reset?
I replaced the belt transfer unit... but it is still giving me the same error code. Is there a master reset function?Comment
-
Ok, before you said you had a message about the transfer belt at end of life. Now you say you have a code?
To clarify, tap the Utility key on the control panel. On the display, touch "consumable life" button.
You will see the image unit, transfer belt and fuser life indicators there. The more "dots", the more used a particular unit is. If you placed a "new" transfer belt, it should have cleared the counter and the indicator should be all white. If it did not clear the counter, you have another problem present.
On the main screen, if you see an "oil can" indication there, touch that. The screen presented will show a list of "P" codes. Tell us what the code is, if any."Many years ago I chased a woman for almost two years, only to discover that her tastes were exactly like mine: we both were crazy about girls."
---Groucho Marx
Please do not PM me for questions related to Konica Minolta hardware.
I will not answer requests or questions there.
Please ask in the KM forum for the benefit of others to see the question and give their input.
Comment
-
You will see 2 chrome right angled pieces of metal on iether side of the area were the transfer belt is undo the screws then the metel pieces spring out toward you then remove the belt ,as for the fuse tis fuse blows when you install a belt and resets the life counter for the belt so replace fuse or replace belt upto you.Comment
-
Error Code C-3423
It won't let me press any buttons. It just says to inform the service technician about "error C-3423"... anybody know what this means?Comment
Comment