bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Laserbeam
    Trusted Tech

    100+ Posts
    • Aug 2011
    • 152
    #1

    [Jamming] bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

    Hello to all,

    today I had a strange problem with a bizhub C454 and finisher FS-534. The paper leaves the paper exit section, but the horizontal transport section (Finisher FS-534) didn't start. After rebooting the machine, usually some copies can be made, but then the old problem is back. By single copies, the machine doesn't display a jam message on the display, only by multiple copies when the backflow comes up in the machine, the jam C3205 occurs.
    As I have seen, the entrance area of the horizontal transport section has no sensors to detect a paper. The command should come from the machine.

    When I use the machine without the horizontal transport section and the finisher, everything works perfect without paper jam problems.

    Please excuse my bad english, but I hope you understand what I wanted to say.
    Attached Files
    Tags: None
    • allan
      RTFM!!

      5,000+ Posts
      • Apr 2010
      • 5459
      #2
      Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

      Was it working before. Did you do firmware. Is there a resonse if you open the finisher door does it show you the doors open?
      Whatever

        Comment

        • blackcat4866
          Master Of The Obvious

          Site Contributor
          10,000+ Posts
          • Jul 2007
          • 22929
          #3
          Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

          My first impression is the the finisher is losing communication with the copier. As a result the MFP intends to eject the paper to the middle tray, but there is a pesky inoperative bridge unit in the way.

          We used to get this all the time when one of our biggest customers would disconnect the full sized finisher to move the machines around, but would then forget to re-connect the cables to the bridge unit. =^..^=
          If you'd like a serious answer to your request:
          1) demonstrate that you've read the manual
          2) demonstrate that you made some attempt to fix it.
          3) if you're going to ask about jams include the jam code.
          4) if you're going to ask about an error code include the error code.
          5) You are the person onsite. Only you can make observations.

          blackcat: Master Of The Obvious =^..^=

            Comment

            • Laserbeam
              Trusted Tech

              100+ Posts
              • Aug 2011
              • 152
              #4
              Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

              The cause is found!!!
              After replacing the middle tray without success, I opened the finisher and saw a broken detecting plate. After exchange with a new one, all works fine.
              Thanks again to all, who have made the effort to answer me!
              Attached Files

                Comment

                • blackcat4866
                  Master Of The Obvious

                  Site Contributor
                  10,000+ Posts
                  • Jul 2007
                  • 22929
                  #5
                  Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

                  Good catch! Were you able to re-set the existing timing wheel, or was it damaged requiring replacement? This is located in the bridge?

                  Thanks for sharing your conclusions. =^..^=
                  If you'd like a serious answer to your request:
                  1) demonstrate that you've read the manual
                  2) demonstrate that you made some attempt to fix it.
                  3) if you're going to ask about jams include the jam code.
                  4) if you're going to ask about an error code include the error code.
                  5) You are the person onsite. Only you can make observations.

                  blackcat: Master Of The Obvious =^..^=

                    Comment

                    • Laserbeam
                      Trusted Tech

                      100+ Posts
                      • Aug 2011
                      • 152
                      #6
                      Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

                      no, I had to renew the timing wheel, because the hold claw was broken. This wheel is located in the finisher (2 of them exists), not in the bridge.

                        Comment

                        • kevan750
                          Junior Member
                          • Sep 2012
                          • 8
                          #7
                          Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

                          Originally posted by Laserbeam
                          no, I had to renew the timing wheel, because the hold claw was broken. This wheel is located in the finisher (2 of them exists), not in the bridge.
                          Do you have the location and part number for this please?

                            Comment

                            • Laserbeam
                              Trusted Tech

                              100+ Posts
                              • Aug 2011
                              • 152
                              #8
                              Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

                              Originally posted by kevan750
                              Do you have the location and part number for this please?



                              Parts number: A3EPPP7402
                              Description: Detecting Plate

                                Comment

                                • splblazer91
                                  Trusted Tech

                                  100+ Posts
                                  • Jul 2014
                                  • 204
                                  #9
                                  Re: bizhub C454 with FS-534 jamming C3205 horizontal transport section didn't start

                                  Take off the lower finisher tray and then remover the cover behind it. Ive had this happen several times. Never replaced one I just use some gorilla glue and have never been called back on one yet.

                                    Comment

                                    Previous template Next
                                    Working...