TA-5500i paper jam 1503

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • stg007
    Technician
    • Dec 2011
    • 14
    #1

    [Error Code] TA-5500i paper jam 1503

    Paper jam 1503, paper does'nt reach paper conveying sensor (PCS), firmware is done as well (3.01), tried new PF-740, changed paper feed section 1 and parts middle roller unit SP. Also changed paper conveying door. Switched primary feed unit 1 and 2.

    If i'm making my copies from cassette 2, no problem occur, only with PF-740.
    Tags: 5500i
    • Metalvoc
      Trusted Tech

      100+ Posts
      • Sep 2008
      • 155
      #2
      Re: TA-5500i paper jam 1503

      When you install the PF-740, you have to install the "intermediate paper conveying unit". Check to see that this is installed correctly, and that the connector on it is fully seated. Also, ensure that none of the screws are missing from the covers in that lower conveying section. I guess it has been a pretty common problem that techs have been neglecting to re-install two particular screws in those covers, causing jams in that area.
      I must have a prodigious quantity of mind; it takes me as much as a week sometimes to make it up - Mark Twain

        Comment

        • stg007
          Technician
          • Dec 2011
          • 14
          #3
          Re: TA-5500i paper jam 1503

          Thank's, i'm a junior member, but a senior tech in mita machine since 1987. In dose case, mickey mouse problems like screws or miss aligment are double check before going higher in solving problems.

          Thank's

            Comment

            • Metalvoc
              Trusted Tech

              100+ Posts
              • Sep 2008
              • 155
              #4
              Re: TA-5500i paper jam 1503

              understood. Most techs with any amount of reasonable experience know to look for simple stuff like that, but from what I understand there have been a significant number of cases where this has happened, or I might not have mentioned it.

              Where exactly does the paper stop? Since you replaced the conveying door, I am guessing it stops in that conveying section, but does it stop just before the PCS, or is it down farther? Does the paper always stop in exactly the same position, or does it appear to be more inconsistent?
              I must have a prodigious quantity of mind; it takes me as much as a week sometimes to make it up - Mark Twain

                Comment

                • stg007
                  Technician
                  • Dec 2011
                  • 14
                  #5
                  Re: TA-5500i paper jam 1503

                  The paper always stop at the same place, half inches before PCS. There's a black guide, has being replaced also.
                  On 20 copies, it jamed 3 to 4 time to make them.

                    Comment

                    • stg007
                      Technician
                      • Dec 2011
                      • 14
                      #6
                      Re: TA-5500i paper jam 1503

                      Problem fixed,

                      The PCS is not one peace sensor, an actuator and the sensor is away. I just bind the frame where the sensor sit, to give more chance of the actuator to come back at the home position quicker.

                      All my jams was after 2 or 3 sheets after the process start of my sets.

                      It was a brand new machine that give me that problems.

                      Thanks

                        Comment

                        • blackcat4866
                          Master Of The Obvious

                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 22984
                          #7
                          Re: TA-5500i paper jam 1503

                          Just to clarify: did you add a wrap to the return spring to make the actuator return more quickly? =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            • stg007
                              Technician
                              • Dec 2011
                              • 14
                              #8
                              Re: TA-5500i paper jam 1503

                              No, just bind the frame who sit the sensor, the actuator will have more distance to come back and where the paper touch the actuator will be more longer outside the hole.

                              It was too fast response before, the paper doesn't have time to go up after the next sheet.

                                Comment

                                • blackcat4866
                                  Master Of The Obvious

                                  Site Contributor
                                  10,000+ Posts
                                  • Jul 2007
                                  • 22984
                                  #9
                                  Re: TA-5500i paper jam 1503

                                  Thanks. =^..^=
                                  If you'd like a serious answer to your request:
                                  1) demonstrate that you've read the manual
                                  2) demonstrate that you made some attempt to fix it.
                                  3) if you're going to ask about jams include the jam code.
                                  4) if you're going to ask about an error code include the error code.
                                  5) You are the person onsite. Only you can make observations.

                                  blackcat: Master Of The Obvious =^..^=

                                    Comment

                                    • Frits
                                      Technician
                                      • Jun 2009
                                      • 62
                                      #10
                                      Re: TA-5500i paper jam 1503

                                      Here the attachment for your problemJam1503.pdf

                                        Comment

                                        Previous template Next
                                        Working...