FS-C5200DN C and Y image problem

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ADI_149
    Technician
    • Dec 2009
    • 10
    #1

    FS-C5200DN C and Y image problem

    Hello.

    I have problem with Kyocera FS-C5200DN. Status Page don't show Yellow and Cyan Toner and there is no Yellow and Cyan image on prints. It's just stopped printing C and Y colors in the middle of the job. I took off everything out like PCU's and Dev Units, cleaned laser shield, cleaned and swapped charging wires ( K with Y), i've done DEV-CLN, LSU/Charger Clean, Drum refresh, checked pins at PWB and Engine Board and nothing. Cyan and Yellow are on diffrent laser scanner motors.

    Total Counter is 40k, firmware 2HN_3000.006.003 2009.10.30

    Any ideas ?

    How to perform DEV-SET ? it asks for 6 HEX chars.
    Tags: None
    • Kidaver
      Ghoulscout

      500+ Posts
      • Apr 2011
      • 912
      #2
      Re: FS-C5200DN C and Y image problem

      the Dev Set is for when you replace the dev units. there will be a number on the parts box that you enter in for the unit.
      "In a cruel and evil world, being cynical can allow you to get some entertainment out of it."

        Comment

        • Tonerkiller
          Senior Tech

          500+ Posts
          • Oct 2012
          • 668
          #3
          Re: FS-C5200DN C and Y image problem

          I had one that was missing one color, and it was because that the reg for that color was so far off that it was not printing that color. That being said, change the color reg for those colors one way then the other and see what happens.

            Comment

            • ADI_149
              Technician
              • Dec 2009
              • 10
              #4
              Re: FS-C5200DN C and Y image problem

              I've found that this is a developing section problem. The developing roller can't move and after manualy rotate roller colors are ok. So i manualy rotate few times for C, Y units and now print's are ok - don't know for how long ;]

              Thx for reply...

                Comment

                • blackcat4866
                  Master Of The Obvious

                  Site Contributor
                  10,000+ Posts
                  • Jul 2007
                  • 22999
                  #5
                  Re: FS-C5200DN C and Y image problem

                  I think this is the same engine as the FS-C2626MFP. If it's the same, it won't last for long, maybe 2 or 3 weeks. My guess is that the developing unit stops replenishing toner for that specific color. I remove the cyan developing unit, squint at it and make my angry face. Then I put it back in and it replenishes. After two visits I ordered and replaced the cyan developing unit. So far OK (fingers crossed) ...
                  =^..^=
                  If you'd like a serious answer to your request:
                  1) demonstrate that you've read the manual
                  2) demonstrate that you made some attempt to fix it.
                  3) if you're going to ask about jams include the jam code.
                  4) if you're going to ask about an error code include the error code.
                  5) You are the person onsite. Only you can make observations.

                  blackcat: Master Of The Obvious =^..^=

                    Comment

                    • JustManuals
                      Field Supervisor

                      5,000+ Posts
                      • Jan 2006
                      • 9838
                      #6
                      Re: FS-C5200DN C and Y image problem

                      This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from


                      Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


                      Paul@justmanuals.com

                        Comment

                        Previous template Next
                        Working...