[Misc] FS1118MFP - Problem printing and photocopying.

[Guest]

I have following problem sending you to print or copy.

When you send a job to the printer that prints the sheet shifted down.
Example: https://www.dropbox.com/s/hacks07zxi...2013194414.pdf

When the sheet comes out, may occur following cases
wrong printed sheet
wrong printed sheet + jam message without it stuck.
wrong printed sheet + jam + jam message in the paper exit.

(Jam message: "Paper Jam in printer JAM40" photo mistake -> https://www.dropbox.com/s/r8z49hmbtj...512_203542.jpg)

The strange thing is that sometimes if it prints well.

Thanks

[zaza]

Re: FS1118MFP - Problem printing and photocopying.

I have following problem sending you to print or copy.

When you send a job to the printer that prints the sheet shifted down.
Example: https://www.dropbox.com/s/hacks07zxi...2013194414.pdf

When the sheet comes out, may occur following cases
wrong printed sheet
wrong printed sheet + jam message without it stuck.
wrong printed sheet + jam + jam message in the paper exit.

(Jam message: "Paper Jam in printer JAM40" photo mistake -> https://www.dropbox.com/s/r8z49hmbtj...512_203542.jpg)

The strange thing is that sometimes if it prints well.

Thanks

well probably you have sensor blocked try cleaner there ..controlled the way when the paper was jammed and seeing there if you have some little paper blocked there ..good lucky

[madas]

Re: FS1118MFP - Problem printing and photocopying.

Rego Clutch.

madas

[JustManuals]

Re: FS1118MFP - Problem printing and photocopying.

This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from:


Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


Paul@justmanuals.com

[Venom]

Re: FS1118MFP - Problem printing and photocopying.

Agree, registration clutch faulty, it is the one in the middle of the 3 in the clutch pack.

[Barış KURT]

Re: FS1118MFP - Problem printing and photocopying.

you must clean residue adhesive of sponge on regist clutch.it reason timing error.

[madas]

Re: FS1118MFP - Problem printing and photocopying.

To test the clutch take it off hold each end and turn it, it should turn freely one way and be solid the other.
if it slips on the side that is meant to be tight it is the clutch, you can clean it and on the lug that is on the big gear that fits in the spring you can put one turn of Sellotape and do not overlap it to much as it will cause a knocking noise this will solve your clutch issue. Done this and got one back with more than 104 k and still solid.
If not the clutch then faulty solenoid rare but happens

madas

[blackcat4866]

Re: FS1118MFP - Problem printing and photocopying.

I'm with madas on this one. Delayed image can be caused by slow pickup or registration clutch. It also fits with the jam conditions you describe. First, the paper is never picked up, thusly you won't find jammed paper. Second, Due to the small size of the machine and loose jam detection criterion, a piece of paper that is picked up late will get all the way to the fuser before the machine determines it's a jam.

If you have an alternate paper source, I'd try feeding from the other paper feed. I think you'll find it doesn't jam. If you narrowed it down to a single paper source, clean or replace rollers, and check the clutches and/or solenoids. Sorry I can't be more specific. I've never worked on this specific Kyocera.

=^..^=

[Pilu]

Re: FS1118MFP - Problem printing and photocopying.

Agree, registration clutch faulty, it is the one in the middle of the 3 in the clutch pack.

Hi there!

I've same problem,hmm and where is find this reg clutch??Can you help me,please If i try mp tray the jam error same but other number...

Always jam 40 error..... and the printing stared the middle of the paper...The Windows test page same like sag user.


Thank you.

[Barış KURT]

Re: FS1118MFP - Problem printing and photocopying.

Hi there!

I've same problem,hmm and where is find this reg clutch??Can you help me,please If i try mp tray the jam error same but other number...

Always jam 40 error..... and the printing stared the middle of the paper...The Windows test page same like sag user.


Thank you.

open right cover machine , all clutchs under the PCB.

[madas]

Re: FS1118MFP - Problem printing and photocopying.

Rarely but it does happen the solonoid fails or the foam pad under the lever comes off and leaves a sticky residue that can hold the lever for a moment and gives the similar rego fault

madas

[Pilu]

Re: FS1118MFP - Problem printing and photocopying.

open right cover machine , all clutchs under the PCB.

Hi,thank you.. I found those...but which is the reg clutch??And what can I do this??Only replace it or the motor is bad?20131104220.jpg

[Pilu]

Re: FS1118MFP - Problem printing and photocopying.

Rarely but it does happen the solonoid fails or the foam pad under the lever comes off and leaves a sticky residue that can hold the lever for a moment and gives the similar rego fault

madas

Behind the Pcb have a registration clutch solenoid. and it's sticky what you wrote ,a little movement help this issue and now the printing perfect.