[Jamming] Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

[LaRueda]

I have been using 2ar07230 for all three rollers and been getting better results than the original rollers to these machines, they have been lasting much longer and was wondering with timing issues with numerous jams cause havent seen any fuser or bridge unit jams.

[tmaged]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

Do you have a question ? If you're having jamming issues, my guess is using the same tires may be causing it. They are treaded in certain directions for a reason.

[stevena86]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

And one of them has a one-way in it and the other does not. How would you even fit the one with a one-way on the lower shaft? I can't see how it'd fit on the shaft, key in to the holder and allow the bushing at the end to seat properly.

[tmaged]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

And one of them has a one-way in it and the other does not. How would you even fit the one with a one-way on the lower shaft? I can't see how it'd fit on the shaft, key in to the holder and allow the bushing at the end to seat properly.

No one-ways on any of these feed tires. There are black, white & gray centers. The feed roller goes on with
with the separate one way to the outside making the tread wrong if you use the other rollers here.

[stevena86]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

The 2AR07220/2AR07230 are the feed rollers for the KM-5050/TA520i series. You're referencing the 302K906350/302K906360/302K906370 rollers.

Unless the OP is also wrong.

[tmaged]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

I stand corrected !

[LaRueda]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

Do you have a question ? If you're having jamming issues, my guess is using the same tires may be causing it. They are treaded in certain directions for a reason.

No questions just would like to let you guys know that these rollers (sep rollers for 5050) run better than original ones to these machine they last longer and have seen less of these machine ever since I started to use these. I had all kind of issues with those black rollers kyocera updated the rollers at one time to grey then went back to the black ones.

[LaRueda]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

The 2AR07220/2AR07230 are the feed rollers for the KM-5050/TA520i series. You're referencing the 302K906350/302K906360/302K906370 rollers.

Unless the OP is also wrong.

I have been using the 2ar07230 for all three the sep, pick up and feed it runs much better than black ones at one time kyocera changed the black ones to grey and used the same one for all three and I know that the black ones do not last they go bad about 50k pages the 2ar07230 last much longer and I tried it at a heavy user as a test to see and they are very much happy now since we are not out as much to replace rollers I'm just giving you guys a suggestion what I have done to improve the feeding on these models

[LaRueda]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

No one-ways on any of these feed tires. There are black, white & gray centers. The feed roller goes on with
with the separate one way to the outside making the tread wrong if you use the other rollers here.

The one way rollers are on the lower speed models thats why I put the higher speed models

[Hawkster]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

Are you replacing the tires in the cassettes only or the LCTs as well

[LaRueda]

Re: Kyocera jamming in trays 4500 to 8000 & 3550 to 7550

Are you replacing the tires in the cassettes only or the LCTs as well

LCTs also. I had great success since I have been using these tires. Hope this will help you out since I know the black rollers are crap, I have told my co-workers about it and thats all they are using also the sep roller for the 5050.