MPC 3002 Bad Print Quality

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • stefan1129
    Guest replied
    Re: MPC 3002 Bad Print Quality

    Using the procedure write by TonerMunkeh print is ok. If the problem reappears, it is possible to reset controller or you need to change controller?
    Thanks,

    Leave a comment:


  • stefan1129
    Guest replied
    Re: MPC 3002 Bad Print Quality

    good morning,
    i have the same problem..there is a way to reset the controller?

    Thanks,

    Leave a comment:


  • BLADE
    replied
    Re: MPC 3002 Bad Print Quality

    Originally posted by Roger67
    Hi Folks,

    after reseting the SP 1101-4 and a new ACC adj. the Machine runs well !

    Thanks for your Help

    Greetings
    Roger
    good one, where do we get the test chart

    Leave a comment:


  • Roger67
    replied
    Re: MPC 3002 Bad Print Quality

    Hi Folks,

    after reseting the SP 1101-4 and a new ACC adj. the Machine runs well !

    Thanks for your Help

    Greetings
    Roger

    Leave a comment:


  • TonerMunkeh
    replied
    Re: MPC 3002 Bad Print Quality

    Okay. It's the ACC that's affecting the copy quality. Run 5-801-008 again and don't ACC the machine.

    Leave a comment:


  • BLADE
    replied
    Re: MPC 3002 Bad Print Quality

    reseat controller

    Leave a comment:


  • Roger67
    replied
    Re: MPC 3002 Bad Print Quality

    After adj. the Machine again with your Infos,the Prints aren t looking good.
    See Att.

    PCL 19.7..pdf

    Leave a comment:


  • TonerMunkeh
    replied
    Re: MPC 3002 Bad Print Quality

    Right. Change SP4-010-001 to -2.0mm. Perform a printer application memory clear SP5-801-008. Reboot. Run SP2-111 modes C then A, then ACC it. That should sort it.

    Also see: http://www.copytechnet.com/forums/ri...ght=4502+gamma

    Leave a comment:


  • Roger67
    replied
    Re: MPC 3002 Bad Print Quality

    Hmmm,there was something special on my ACC Test Charts........please see the Att.

    ACC.pdf

    Cheers
    Roger

    Leave a comment:


  • TonerMunkeh
    replied
    Re: MPC 3002 Bad Print Quality

    Oh hang on, I think I know what's going on here. Print out a printer ACC test pattern. Are the first 8 or 9 sections really pale then the the last 5 or 6 solid as anything?

    Leave a comment:


  • Roger67
    replied
    Re: MPC 3002 Bad Print Quality

    Using the PS 3 Option,even the Print Quality is much more worst than the Examples with the
    PCL Driver.

    See att.

    PS Driver.pdf





    Printing the same File on a MPC 4503 using the PCL Driver,the Quality is good.
    We almost changed every Board,the Novram etc. in the Defectiv MPC 3002.......

    Now we dont now,what to do !

    Cheers
    Roger

    Leave a comment:


  • TonerMunkeh
    replied
    Re: MPC 3002 Bad Print Quality

    Bearing in mind you're using an office MFP using the PCL driver and not Postscript, the shift in resolution will cause the machine to use more process black in the image creating your colour differential. You're never going to get a perfect colour match on this machine.

    Anyhoo run line position adjustment, run process control and then ACC it. Make sure all your PM parts are in life.

    On a lighter note, that is some epic sideboob.

    Leave a comment:


  • Roger67
    started a topic MPC 3002 Bad Print Quality

    MPC 3002 Bad Print Quality

    Hello,

    i have a problem with a MPC 3002 during print outputs with higher resolution.

    With 1200 x 1200 dpi the resolution in the black parts of the Pic looks good.
    With 2400 x 600 dpi the resolution in the black parts of the Pic looks bad.

    See att.

    Im using a PCL 6 Driver and the FW: PCL 1.15 / System 2.16 / Engine 1.10:04 / PDF 1.04


    Thanks for help

    Roger

    MPC 3002.pdf
Working...