Ricoh C2003 - print job will do after re-close duplex unit

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • NeoYoung
    Junior Member
    • Oct 2020
    • 4
    #1

    [Misc] Ricoh C2003 - print job will do after re-close duplex unit

    as i describe in title, motors are not working after i press start for print job and counter list. Print jobs will work after i re-close duplex unit. But this problem will happen again when i reboot machine. Is there anyone experienced the same problem like this?
    Tags: duplex, print, re-close, unit
    • slimslob
      Retired

      Site Contributor
      25,000+ Posts
      • May 2013
      • 37047
      #2
      Re: Ricoh C2003 - print job will do after re-close duplex unit

      Check the Service Code log for any type C errors at power up. These are non fatal errors that are counted and logged only, they are not displayed.

        Comment

        • NeoYoung
          Junior Member
          • Oct 2020
          • 4
          #3
          Re: Ricoh C2003 - print job will do after re-close duplex unit

          i found SC552-02, check Fusing Temperature with SP MODE 1-106, it is 45 deg after standby for a while, after re-close duplex unit, it will be 110 deg and work for print.

            Comment

            • slimslob
              Retired

              Site Contributor
              25,000+ Posts
              • May 2013
              • 37047
              #4
              Re: Ricoh C2003 - print job will do after re-close duplex unit

              Clean/check/replace the fusing thermopile unit. Located in the body of the C2003 just above the connector for the fusing unit. After removing the fusing unit two connectors and two screws to remove.

                Comment

                • mga
                  Copier Technician

                  Site Contributor
                  1,000+ Posts
                  • Dec 2010
                  • 1393
                  #5
                  Re: Ricoh C2003 - print job will do after re-close duplex unit

                  Thermopile errors could also be given from faulty connections in fuser unit unplug all connectors ie thermistors etc and rear of main connector big blue one before reconnecting make sure no pins are push slightly out. Good luck
                  Regards Mark

                  FOR TRADE AND END USER SERVICE CALLS PLEASE VISIT WEB SITE FOR CONTACT DETAILS. COVERING GREATER LONDON {UK} AND ALL SURROUNDING COUNTIES.

                  RICOH, CANON, KYOCERA, KONICA, SHARP, HP/SAMSUNG BROTHER, LEXMARK.

                  https://copierservices.simdif.com

                    Comment

                    • NeoYoung
                      Junior Member
                      • Oct 2020
                      • 4
                      #6
                      Re: Ricoh C2003 - print job will do after re-close duplex unit

                      Thank you all for advice. Finally, i fixed it by clear counter of fuse.

                        Comment

                        • davel
                          Technician

                          1,000+ Posts
                          • Oct 2011
                          • 1089
                          #7
                          Re: Ricoh C2003 - print job will do after re-close duplex unit

                          Not permanent fix.

                            Comment

                            • NeoYoung
                              Junior Member
                              • Oct 2020
                              • 4
                              #8
                              Re: Ricoh C2003 - print job will do after re-close duplex unit

                              Originally posted by davel
                              Not permanent fix.

                              indeed, because i have change every sensor and parts related with fuse and electric board.

                                Comment

                                • Phil B.
                                  Field Supervisor

                                  10,000+ Posts
                                  • Jul 2016
                                  • 22798
                                  #9
                                  Re: Ricoh C2003 - print job will do after re-close duplex unit

                                  Originally posted by NeoYoung
                                  indeed, because i have change every sensor and parts related with fuse and electric board.
                                  ahhhhh the old 'shotgun' approach to repairing a unit. expensive.

                                    Comment

                                    • slimslob
                                      Retired

                                      Site Contributor
                                      25,000+ Posts
                                      • May 2013
                                      • 37047
                                      #10
                                      Re: Ricoh C2003 - print job will do after re-close duplex unit

                                      Originally posted by Phil B.
                                      ahhhhh the old 'shotgun' approach to repairing a unit. expensive.
                                      But sometimes necessary. Decades ago I worked on Vydec word processors. 20+ boards. A board could be within design specs on its output and the board it was talking to could be within design specs on its input but you could still get random errors if one board was to of extreme of the specs and the 2nd board to the other extreme. It was pick one and replace it. If that didn't work try the other. Tag the board with a description of the error. When I got the same error on 3 or more machines I would send the board to the repair depot. Component level techs had a list of what to replace passed on reported error.

                                        Comment

                                        Previous template Next
                                        Working...