mpc3003 offset (ghost image) after sleeve unit replaced

[Gift]

Re: mpc3003 offset (ghost image) after sleeve unit replaced

We also have this every now and then - some sorts of paper/enviroments aren't running well without a little "temp boost". I think normal paper setting is used to a maximum of 81g/m2 - not much of a margin there to compensate for poor paper. If the customer is using color copy paper 90g/m2 you shuld set it on medium anyways

[Mark Bbb]

Re: mpc3003 offset (ghost image) after sleeve unit replaced

Can you go into service mode and find the fuser settings for the different types of paper? Just take the settings for medium thick and apply them to plain paper.

These settings i have put in plain paper. Although it is better, it is no solution. Notice that M-thick FC center is going to low speed; how should i set that up???
So, "Medium thick" seems to be the only solution. I do not understand why Ricoh don't take any steps. And i do not understand why i'm the only one that seems to have this problem?

014 M-thick:FC:Press *ENG [0 to 200 / 120 / 1 deg/step]
015 M-thick:BW:Center *ENG [100 to 180 / 150 / 1 deg/step]
016 M-thick:BW:Press *ENG [0 to 200 / 120 / 1 deg/step]

109 M-thick:FC:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
110 M-thick:FC:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]
111 M-thick:BW:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
112 M-thick:BW:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]

[mga]

Re: mpc3003 offset (ghost image) after sleeve unit replaced

These settings i have put in plain paper. Although it is better, it is no solution. Notice that M-thick FC center is going to low speed; how should i set that up???
So, "Medium thick" seems to be the only solution. I do not understand why Ricoh don't take any steps. And i do not understand why i'm the only one that seems to have this problem?

014 M-thick:FC:Press *ENG [0 to 200 / 120 / 1 deg/step]
015 M-thick:BW:Center *ENG [100 to 180 / 150 / 1 deg/step]
016 M-thick:BW:Press *ENG [0 to 200 / 120 / 1 deg/step]

109 M-thick:FC:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
110 M-thick:FC:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]
111 M-thick:BW:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
112 M-thick:BW:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]

Hope this helps

[Mark Bbb]

Re: mpc3003 offset (ghost image) after sleeve unit replaced

Hope this helps

SP1-106-1 is a temperature display mode. No adjustment can be made there.


This T.B. is for MET-C1b, is that c3003?

[mga]

Re: mpc3003 offset (ghost image) after sleeve unit replaced

SP1-106-1 is a temperature display mode. No adjustment can be made there.


This T.B. is for MET-C1b, is that c3003?

Yes covers mpc3003 3503 4503 5503 6003 you need to make sure you you set for mpc3003

Also do this
3612-131-132-133-134 K.,C,M&Y
SET ALL TO 600