[Jamming] Ricoh mp 9000

[khaled_abosere3@yahoo.com]

Our problem concentrate that suddenly when we making any copy paper stopped at entry of fusing unitwe made output check on fusing motor found it not working there is no any service code appear to confirm that fusing motor is defective or any thing else.With my greetings.

[rsyarcia]

Re: Ricoh mp 9000

isolate first if what sensor is detecting the jammed paper. check logs.

[vargue]

Re: Ricoh mp 9000

revealed your skills where paper jam. watch what make jam. fingers/ fuser gate / etc sensor then jam with first paper or with heavy works.some thread must be watched

[imaginemoko]

Re: Ricoh mp 9000

if it happes that the machine give Jam 21... and not even a single paper is not passing it tends to be the fusing drive motor is the problem. basically the motor will run when you make output check... the problem there is that the white gear inside that motor has loose its grip to the shaft that why it does'nt drive... anyhow Good Luck Sadiq... Salam.

[Coptech]

Re: Ricoh mp 9000

HR Gear

[khaled_abosere3@yahoo.com]

Re: Ricoh mp 9000

revealed your skills where paper jam. watch what make jam. fingers/ fuser gate / etc sensor then jam with first paper or with heavy works.some thread must be watched

My dear sweet as i wrote that when making output check the motor does not drive.

[slimslob]

Re: Ricoh mp 9000

My dear sweet as i wrote that when making output check the motor does not drive.

Is it that the motor does not run or that the hot roller does not turn? If the latter, see what see what coptech said. HR = hot roller.

[imaginemoko]

Re: Ricoh mp 9000

have we try to check physically this motor? or even test it on other machine? hot roller gear is metal so it wont worn out that easily. sometimes the motor that drive the hot roller does come back to engage it has a spring and in time it accumulate rust.

[Coptech]

Re: Ricoh mp 9000

Where are you seeing a metal HR gear on an MP9000? They didn't use metal until they got to the D101 line. Am I wrong?

[khaled_abosere3@yahoo.com]

Re: Ricoh mp 9000

Is it that the motor does not run or that the hot roller does not turn? If the latter, see what see what coptech said. HR = hot roller.

Both of them do not run if fusing motor or hot roller.

[Imprestik]

Re: Ricoh mp 9000

Remove the fuser and run in output check the fuser motor by cheating the door switches

If the motor is turning I can bet you the drive motor is on a spring tension and the spring has got stuck in the frame causing the fuser not to drive or due to rust the spring and shaft are not releasing

Just add a touch of oil and manually push the shaft/spring in and out a couple of times until it feels free

If you find the fuser motor is not rotating with the fuser out of the device in output check, just order a new fuser drive motor

[imaginemoko]

Re: Ricoh mp 9000

Where are you seeing a metal HR gear on an MP9000? They didn't use metal until they got to the D101 line. Am I wrong?

Sir Aficio MP 9000. 90 copies per minute, Bellini C3, known to be Katana (B234). or maybe its me who's wrong... my apologies.

[Coptech]

Re: Ricoh mp 9000

Sir Aficio MP 9000. 90 copies per minute, Bellini C3, known to be Katana (B234). or maybe its me who's wrong... my apologies.

You are not wrong. I stand corrected. The B234 is a metal gear machine. Go with the spring loaded drive theory or the motor itself, or drive board. The strategy of cheating the front door and watching the drive with the fusing drive selected in the output mode is a good one.

[redneckstylin]

Re: Ricoh mp 9000

Spin the knob on fuser does your rollers turn if not head to back of fuser and you will find a broken gear of doom replace gear and you will be back up and running sipping on a cold beverage after