Help with code MX-4141N

[campy]

I don't know why I can never find what I am looking for in the manual. I am getting a message that says Maintenance Code TA. I thinks it's the Transfer belt but not sure. If it is, what needs to be done and if you have the part numbers I would appreciate it. I am more a Canon guy but I have a customer that has 6 Canons and 2 Sharp 4141. It has 431K on it.

[driving lots of miles]

Re: Help with code MX-4141N

TA stands for the replacement timing of the fusing cleaning
roller, the filter and PS paper dust removal cleaner. there are
usually more codes also involved and they should show up on the machine.

[harleyrider]

Re: Help with code MX-4141N

look in the maintenance section .

[JLSam]

Re: Help with code MX-4141N

It's in the service manual. "Display of maintenance execution timing". Section 9 - 2.

Basically, it's DK and VK combined. Needs the new black kit.

Developer, drum, blade, and charger.

Drum: mx31nrsa
Kit: mx510mk
Dev: mx51nvba

Reset codes in sim 24.

Good luck.

Sent from my ONEPLUS A3000 using Tapatalk

[JLSam]

Re: Help with code MX-4141N

TA stands for the replacement timing of the fusing cleaning
roller, the filter and PS paper dust removal cleaner. there are
usually more codes also involved and they should show up on the machine.

Fusing cleaning would be FK3.

But I agree, he should check for other codes in MFP status.

Sent from my ONEPLUS A3000 using Tapatalk

[copierdude1114]

Re: Help with code MX-4141N

You can always check sim 22-13 if you aren't sure, show's you the remaining life %'s

[mttech]

Re: Help with code MX-4141N

If you have access to the copier you can print out a sim 22-6. On the first page will be the sim 22-13 info. This will also give the percentage of life use.

[dwarf]

Re: Help with code MX-4141N

A. Maintenance
Maintenance required. Code: TA 0 (Print continue) Maintenance counter
(Total)
When the SIM21-1 set value is reached. Enable
1 (Print stop) When 90% of the SIM21-1 set value is reached.
Maintenance required. Code: TA 1 (Print stop) When the SIM21-1 set value is reached. Disable
Maintenance required. Code: CA 0 (Print continue) Maintenance counter
(Color)
When the SIM21-1 set value is reached. Enable
1 (Print stop) When 90% of the SIM21-1 set value is reached.
Maintenance required. Code: CA 1 (Print stop) When the SIM21-1 set value is reached. Disable
Maintenance required. Code: AA 0 (Print continue) Both of total and color When the SIM21-1 set value is reached. Enable
1 (Print stop) When 90% of the SIM21-1 set value is reached.
Maintenance required. Code: AA 1 (Print stop) When the SIM21-1 set value is reached. Disable
Display content
Display condition Print JOB
SIM26-38-A set value Counter name Counter value Enable/Disable
Maintenance required.: TK1 0 (Print continue) Primary transfer unit print counter When 300K is reached. Enable
1 (Print stop)
Display content
Display condition Print JOB
SIM26-38-A set value Counter name Counter value Enable/Disable
Maintenance required.: TK2 0 (Print continue) Secondary transfer unit print
counter
When 300K is reaches. Enable
1 (Print stop)
Display content
Display condition Print JOB
SIM26-38-A set value Counter name Counter value Enable/Disable
Maintenance required.: FK1 0 (Print continue) Fusing belt print counter When 300K is reached. Enable
1 (Print stop)
Maintenance required.: FK2 0 (Print continue) Pressure roller print counter Enable
1 (Print stop)
Maintenance required.: FK3 0 (Print continue) Fusing web print counter Enable
1 (Print stop)
Display content
Display condition Print JOB
SIM26-38-B set value Counter name Counter value Enable/Disable
Maintenance required.: FK3 0 (Print continue) Fusing web print counter When 300K is reached. Enable
1 (Print stop)
Maintenance required.: FK3 0 (Print continue) Fusing web print counter When Web end detection is ON Enable
1 (Print stop) Enable
Display content
Display condition
Print JOB
SIM26-38-A Enable/Disable
set value Counter name Counter value
Maintenance required.: DK 0 (Print continue) OPC drum print counter (K) or
OPC drum accumulated rotation number counter (K)
840K is reached
or 200K is reached
Enable
1 (Print stop)
Maintenance required.: D (C/M/Y) 0 (Print continue) OPC drum print counter (C/M/Y) or
OPC drum accumulated rotation number counter (C/M/Y)
840K is reached
1 (Print stop) or 160K is reached

[fireater]

Re: Help with code MX-4141N

I don't know why I can never find what I am looking for in the manual. I am getting a message that says Maintenance Code TA. I thinks it's the Transfer belt but not sure. If it is, what needs to be done and if you have the part numbers I would appreciate it. I am more a Canon guy but I have a customer that has 6 Canons and 2 Sharp 4141. It has 431K on it.

maintcodes
D (k/c/m/y) drum the letteres are cyan magenta yellow and black
V(k/c//m/y) developer .. letters are same as drums
TA maint black
CA maint colour
TK1 primary transfer
TK2 secondary transfer
TK3 not in book PTC
FK1 Fusing belt
FK2 Lower Pressure roller
FK3 Fusing Web