sharp ar c260m l4-06/07

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • sc3
    Technician
    • Mar 2011
    • 20
    #1

    [Error Code] sharp ar c260m l4-06/07

    Hello I got a transport code tried different transport machine still coded. tried replacing belt on old unit still code. checked lift seems fine. has anyone ran into this back when it was relevent, and can remember what it was. thanks.
    SC3
    Tags: arc260m, back, belt, code, lift, sharp, sharp codes, transport, unit
    • blackcat4866
      Master Of The Obvious

      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22997
      #2
      Re: sharp ar c260m l4-06/07

      I found this record in the database, but have no memory of the event:

      "L4-07" after maintenance. "Errors, Others_Error" resulting from Auto Registration sim 50-22. In Manual Registration C2: -1, M2: -4, Y2: -7. Cracks in the transfer belt catch on the blade slowing or stalling the transfer belt motor. Replace & prime the transfer belt with titanium stearate. Re-run simulation 50-22, 50-20, etc.

      =^..^=
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • Dark Helmet
          Senior Tech

          Site Contributor
          500+ Posts
          • May 2009
          • 835
          #3
          Re: sharp ar c260m l4-06/07

          I had a very fussy BC320 that would throw that code. In the end we had to replace the entire transfer unit with a new one from supplies (it was cheaper than getting it through parts). I think it was over 300 bucks. I did the same thing with swapping from a used machine, rebuilding etc etc. The code would keep coming back. I hate those machines.

          I was told the connector can get buggered up in the machine and cause codes as well but i never saw it.
          Evil will always triumph because good is dumb.

            Comment

            • brewster67
              Trusted Tech

              Site Contributor
              100+ Posts
              • Jul 2011
              • 167
              #4
              Re: sharp ar c260m l4-06/07

              The connector on the machine side can get caught and cause these codes. If you pull the transfer belt out you should be able to reach in and push the connector. It is on springs and will push in and come back out. If it gets into far the connector can catch on the side of the bracket and not come back out.
              The other thing to check is to pull the transfer belt and pull the cover off the drive gear and spin the belt by hand. If the belt slips then it will give you problems and the easiest thing to do is replace it.

                Comment

                • blackcat4866
                  Master Of The Obvious

                  Site Contributor
                  10,000+ Posts
                  • Jul 2007
                  • 22997
                  #5
                  Re: sharp ar c260m l4-06/07

                  Another thing that will cause this is forgetting to remove the tension screws & protection sheet. =^..^=
                  If you'd like a serious answer to your request:
                  1) demonstrate that you've read the manual
                  2) demonstrate that you made some attempt to fix it.
                  3) if you're going to ask about jams include the jam code.
                  4) if you're going to ask about an error code include the error code.
                  5) You are the person onsite. Only you can make observations.

                  blackcat: Master Of The Obvious =^..^=

                    Comment

                    • sc3
                      Technician
                      • Mar 2011
                      • 20
                      #6
                      Re: sharp ar c260m l4-06/07

                      Thanks I'll try to check all of those things.
                      SC3

                        Comment

                        Previous template Next
                        Working...