help for reset e-studio 25-35-45

[alexi_issa]

HDD

plz ,if i want 2change the hard disk ,so what is the programe to format it ,plz give me the way to use new HDD

[oliver]

F100 - HDD error

reset this error code in 08-690 set to 2 and start. It will "format" the HDD and hopefully resolve this issue. if not you may need to replace the HDD.

[alexi_issa]

ok 10x but i know this code but i have a problem with my HDD.

[burakco]

can i reset trial mode for network fax/printer ?

[ivovb]

can i reset trial mode for network fax/printer ?

No, sorry. U can only stop it if U activated it previously.
BR

[ivovb]

ok 10x but i know this code but i have a problem with my HDD.

If U talking about e450 U will need (as Mr Spock says already):
1. new 40Gb HDD PATA set for cable sellect.
2. firmware to load in HDD.

If U talking about e45 just change the HDD. U might need UI firmware but it depends of user language that U need to set on display.
BR

[Nazakat]

F100 is about HDD Initialization. 08 - 690 is the code for formatting. Reboot the machine occures if HDD is formated successfully.IF an error occured, Replace HDD.











Toshiba has no Technical support in Pakistan But......Main Hoon na

[Nazakat]

Its HDD Format Error. 0+8 ---690 is the Code to format HDD.It will take 15 to 40 seconds to show reboot the machine.If it never comes and machine remains "wait" Position, Replace the HDD.










Toshibians in Pakistan.......eat my dust.

[arriva1]

F100 Other service call HDD format error: HDD cannot be initialized normally.
P. 5-91
F101 HDD unmounted: Connection of HDD cannot be
detected.
P. 5-91
F102 HDD start error: HDD cannot become ‘Ready’ state. P. 5-91
F103 HDD transfer time-out: Reading/writing cannot be
performed in the specified period of time.
P. 5-91
F104 HDD data error: Abnormality is detected in the data
of HDD.
P. 5-91

F105 HDD other error P. 5-91
1st try to reformat hard drive With 08-690

[F100] HDD format error

(1) Check if the HDD is mounted.
(2) Check if the specified HDD is mounted.
(3) Check if the connector pins of the HDD are bent.
(4) Check if the power supply connector is disconnected.
(5) Check if the connector J111 on the SYS board is disconnected.
(6) Replace the harness.
(7) Initialize the HDD. (Key in “2” at 08-690.) (I would try this first)
(8) Replace the HDD.

(9) Replace the SYS board.

[Nazakat]

Yes it can be reset. The Trial Period in 350/450 , 352/452. I have done it.














In Pakistan Toshibians are eating my dust.

[burakco]

Yes it can be reset. The Trial Period in 350/450 , 352/452. I have done it.

how did you do it,can you tell me?

you can mail me to burak_co@hotmail.com or here . . .

[burakco]

Hard drive failure. You will need to replace and reload the operating system (firmware on this model).

how can i replace and reload the operating system? could anybody explain to me?

[jawir]

Hi,

F100 is problem in HDD. You can try format it by using 08+690 than input value 2 to Format the hardisk than press start button. Wait until reboot the machine appear in the control panel. after that reboot the machine. if this cannot solve the problem, you may change HDD with the new one.

regards

[yemifest]

e-studio 351c CEB0 error code

Hi my friends
please kindly tell me what CEB0 error code on toshiba studio351c 0r 3511 means ...

[Nazakat]

Brother

Its Black Developer unit lifting movment Abnormality.Possibly cause by Little cover under the Waste Bottle. Check the cover and adjust it.
Black Developer contact position detection sensor or Black developer contact timing detection secsor can cause this problem. Check and rectify.





In Pakistan Toshibians are eating my dust