eStudio 2330c Parts Manual

[joethethird]

Folks,

I am in need of a parts manual for a Toshiba eStudio 2330c. I have purchased and downloaded TWO Service Handbooks for this model. The manuals I have purchased include the Service Handbook for the 2020C,2330C, 2820C, 2830C, 3520C, 3530C & 4520C but the included Service Parts List does NOT include the 2330c. WTH! The Service Parts List includes 2820C, 2830C, 3520, 3530C & 4520C but NOT the 2330c. I need the paper lift gears that the metal lift assembly on the paper drawer engage to lift the tray. The gear front where the steel pin on the paper drawer engage is broken. They are NOT the same gear as the models I listed as included in the Service Parts List in the manual I bought. Any help in this matter would be appreciated. I have no way to order those gears without the part number. Thanks

[arnh79]

Re: eStudio 2330c Parts Manual

Parts list for an e2830c would be identical to e2330c, except for LGC board. Lifters are same on the entire series.

[rapidocument]

Re: eStudio 2330c Parts Manual

I have the full technical documentation disk for these series and the parts manual is only one, (the one that you have), for all other options there are separate manuals but for the main frame there's only one, by the way here is a link for precision roller where it shows that the lift unit is common to several models

Toshiba E STUDIO 2330C Tray Lift Unit, Genuine (M9168)

[blackcat4866]

Re: eStudio 2330c Parts Manual

You know, if your parts don't seem to be matching up, it's fully possible that another model of that series got substituted on a visit to the shop, as a method to overcome an insurmountable problem.

It had that exact situation on a eStudio 3500 that was masquerading as an eStudio 3510. Before it had come under our service the machine had undergone a cover swap, so it still looked just like an eStudio 3510. When the second Logic board still did not have the correct connector configuration we started examining the other models in the family, until we found what it really was. Another way to confirm is to check the internal reports.

=^..^=

[joethethird]

Re: eStudio 2330c Parts Manual

rapidocument & blackcat

2330c-Funtcion-List.jpg2330c-Serial-Plate.jpg2330c-Front-Cover.jpg

Rapidocument, I have the service parts list for the 2330c-Base-Frame-Part-Numbe.jpg2330-Base-Frame-Parts.jpg

If you reference the part illustration part number 3 is the paper lift gear part number 41306022000. I ordered two of these from Precision. Precision does not have a photo on their site. The gears are NOT for the machine I am attempting to repair. These are the gears.

2330c-Gear-in-Bag.jpg2330c-White-Gear.jpg



2330-Paper-Lift.jpg2330c-Paper-Lift-Assembly--.jpg2330c-Paper-Lift-Number.jpg

[blackcat4866]

Re: eStudio 2330c Parts Manual

I think you'll find that even though they are different colors, the white one is essentially the same part ... just white.

Another possibility, is that a used lift motor from a e Studio 350 got installed. It's exactly the same ... just black. =^..^=

[joethethird]

Re: eStudio 2330c Parts Manual

David, the white gear I orderd is for the eStudio 350. It is completely different than the gears inside the black paper lift assembly from the machine in question. Here is the link to Precision Roller's page.

Toshiba E STUDIO 350 CPG Lift Gear, Genuine (H4164)

That gear has the part number listed in the service parts list for the 2330c. Its possible that the lift unit in the machine I'm working on is from a model other than a 2330c but I have no way of knowing which model. I may have to order the entire assembly with the part number that Jaime (rapidcoument) posted. The Precision Roller page did indeed list it as being for the 2330c. Any other tips would be appreciated.

Thanks,

Joe Lopez III

[vstar]

Re: eStudio 2330c Parts Manual

Hi everyone, I was wondering if anyone would have a part number for the paper feed guide. This guide is inside the side door below the duplex and bypass section. One of the pivot points broke off and the Intravia guide doesn't seem to list it.
Any help would be appreciated.

Thanks

Cameron

[blackcat4866]

Re: eStudio 2330c Parts Manual

Do you have a picture of what you want? =^..^=

[vstar]

Re: eStudio 2330c Parts Manual

Sorry I don't have a pic. It is a black guide that tilts out when you open the door. The paper runs between it and the inside part of the machine. If you had the parts manual the shows the feed section for the second tray or right side covers it would probably be in there. Or verticle transport area.

Thanks for any help.

Cameron

[riyadh hossainbd]

Re: eStudio 2330c Parts Manual

I think you'll find that even though they are different colors, the white one is essentially the same part ... just white.

Another possibility, is that a used lift motor from a e Studio 350 got installed. It's exactly the same ... just black. =^..^=

Black box and white box are different .But if someone change total box it will work ,if change some white gear into black box it may not be set

[didi2005]

Re: eStudio 2330c Parts Manual

CaseTray.jpg

[mbal]

Re: eStudio 2330c Parts Manual

Do you have a picture of what you want? =^..^=

Blackcat4866, here are some pics of the part vstar is referring too. First shows drawer position, second shows view of the black paper feed tray inside that's broken.

IMG_09202.JPGIMG_09192.JPG

[vstar]

Re: eStudio 2330c Parts Manual

Thanks mbal, that black guide that pivots in the second pics is what I am looking for. Thank you so much for posting the pics. We are a Lanier dealer but a customer has this machine also.
If I can get a part number maybe I can find it or have precision order it for us.

Thanks again

Cameron

[vstar]

Re: eStudio 2330c Parts Manual

Would someone be able to give me the parts number?

Thanks

Cameron