Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • pkt.hoangquan
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Hi Bros,
    I had the same trouble on my B&W Altalink B8145 when i installed new HDD.
    I created a USB alboot
    placed it inside:
    DISABLE_DATA_BACKUP
    FORCED_UPGRADE
    XeroxAltalink_B8145-B8155_ALTBOOT_system-sw#11401301128800#ENG_MOD
    I cannot downloaded the Special Alboot folder.
    I need your help to solve my trouble.
    Thank you!

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Thank you!!!! The device is working! exactly helped-special alboot!!!
    super forum!!! Good people!!! Thank you!!

    Leave a comment:


  • xcopytech
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Yes special usb cable

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    pws altboot must be done via USB cable?

    Leave a comment:


  • xcopytech
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    You have to use all files from same software level.
    Full software is about 750mb and if usb altboot do not help then pws altboot is only solution

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    yeah, I know ! I found exactly the required firmware file, but did not create the folder ---EFI
    with the download files .... and so the machine updated normally and updated all the components and after the reboot it began to ask for a password ... I met people who did it according to the same scheme and the result was like mine ....
    they promised to give me all the files like in your photo with...


    Thank you so much for this special upload photo!

    Leave a comment:


  • xcopytech
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Dlm file from xerox site is for customer to upgrade working machine.

    Leave a comment:


  • kropa
    replied

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    [QUOTE=xcopytech;2575998]Для специальной altboot вам нужны дополнительные файлы, а не только файл программного обеспечения dlm.[/ЦИТАТА]

    Thanks, it's clear now! I probably restore these files in the machine to their initial value. Only the service center has these files, I think so. Or you can find them...
    I added another file, maybe this is it?

    583601v2a.dlm ---------------Is it this particular file that is special?
    DISABLE_DATA_BACKUP
    FORCED_UPGRADE

    Leave a comment:


  • xcopytech
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    For special altboot you need additional files not just dlm software file.
    Attached Files

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    This recovery procedure has appeared for altalinks 80xx and 81xx. In addition to the dlm, a directory with a bootloader is added to the flash drive, which allows you to restore the machine after replacing the disk or memory card. With a high degree of probability, all billing will be lost on the 80xx machine.


    this is what I need?

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Данная процедура восстановления появилась для altalinks 80xx и 81xx. Помимо dlm на флэшку добавляется директория с загрузчиком, что позволяет восстановить аппарат после замены диска или карты памяти. С большой долей вероятности на машине 80хх будет потерян весь биллинг.


    это то, что мне нужно?

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    clear



    ya sozdal papku



















    15 / 5 000






    Результаты перевода

    Перевод

    I created a folder







    clear



    ya sozdal papku



















    15 / 5 000






    Результаты перевода

    Перевод

    I created a folder alboot
    placed it inside:
    DISABLE_DATA_BACKUP
    FORCED_UPGRADE
    XeroxAltalink_C8170_ALTBOOT_system-sw#11401101128800#ENG_MOD.DLM

    that's all what I know.

    Leave a comment:


  • kropa
    replied
    Re: Altalink C8170 Enter Current Password Message is Displayd at Start Up !!!

    Is this what flashes each component again, changing everything old?

    Leave a comment:


  • kropa
    replied

    Leave a comment:

Working...