workcentre pro c3545 help PLZ

[rabib]

thank you xcopytech

but whats the solutiiiiiiiiiiiiiion plz ???????

[rabib]

I have one question is that the fiery c3535 same c3445 ????????????

wcp c3535 and c4535 becausemy friend have the wcpc3535 fiery


(sorry for my bad english ^ _* )

[xcopytech]

try with new ccm nvm or ccm pwb.
and if your friend have dc 3535, controller is not same.
you can use controller from wcp 2128/2636/3545

[rabib]

OK Thank you x copytech ^_*

[simpel]

where can you buy a CCM NVM PWB?

[simpel]

I am trying to connect the printer with alternateboot. The following error will be displayed. the printer starts up over and over again. c3545

"
LynxOS (x86) created Thu Apr 14 13:27:16 EDT 2005
***** DMA-enabled IDE disk driver *****
Copyright 1993 Xerox Corporation Version ROM
Running fsck on [/dev/hd0b], Please Wait ...
(all sizes and block numbers in decimal)
(block size is 2048)
(file system is byte-swapped)
(file system creation time is Sat Jul 17 17:12:53 2010)
(file system contains 104832 blocks and 26208 inodes)
checking used files
checking for orphaned files
making bit map free block list
making free inode list
99482 free blocks 25871 free inodes
Filesystem Ok

Running fsck on [/dev/hd0a], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0e], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0h], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0f], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0i], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0j], Please Wait ...
Filesystem Ok

Running fsck on [/dev/hd0k], Please Wait ...
Filesystem Ok

rc.custom1 is allowing the pci_enet DLM to install the i82559 Enet Driver!
Atlanta Board Detected... Installing ELT and NPLI(SMC) Drivers
Begin cleanup...
...cleanup finished.
drinstall -c ./smcDriver
./smcDriver installed on driver id 31
generate ./smcInfo
devinstall -c 31 ./smcInfo
PCI Bus NPLI Driver
npliDriver::Could not allocate device space
devinstall: ./smcInfo: Device or address doesn't exist
Failed to install ./smcInfo



**** LynxOS is down ****

"
what does NPLI driver do?

[simpel]

nobody installs new boot software?

[simpel]

[ATTACH=CONFIG]4109[/ATTACH]


Thanks xcopytech

but same problem

[ATTACH=CONFIG]4107[/ATTACH]

Change the C to a S

map: C0_01_04.511 => S0_01_04.511
file ecnC0304510.140 => ecnS0304510.140
file in the upgrade map: ecnC0304510.dlm => ecnS0304510.dlm

can anyone tell me why it is a C ?

[simpel]

This is not true. With the zipfile c0_01_04.511 you can update the ESSplatform and UIplatform to version 511/510.
For the DCplatform ( System Software Version) you need another file.

My software is still 01.04.044 does anybody got an upgradefile?

Should be something like: C3545/inst/S0_01_04_505/

[seximibabay07]

Re: workcentre pro c3545 help PLZ

Hello friend, do you have FIRMWARE and WPS Diagnostics tool for WorkCentre Pro C2128?
Best regards;