Xerox wc 7125 error

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • xeroxsharp
    replied
    Re: Xerox wc 7125 error

    Originally posted by landspeeder
    The error is 092-315 any one have ideas??? Also does any one have a service manual??? sigh

    thanks
    Already work with this issue. Colour copies are good!
    If you use another new black drum and get same resault / faulty main drive assembly
    Main drive must be replaced / PN 007K16690 / FIRST TIME 1-2 hours of work
    Fault can not be cleared by resetting chains 752-368 and 752-372 to 0

    BR

    Leave a comment:


  • adriansto
    replied
    Re: Xerox wc 7125 error

    You need PWS for use the edoc.
    stoadis@gmail.com

    Leave a comment:


  • landspeeder
    replied
    Re: Xerox wc 7125 error

    I have GSNlock as we are Xerox auth. on a lot of models but not that one...and time is short on this issue!!
    Thanks

    Leave a comment:


  • landspeeder
    replied
    Re: Xerox wc 7125 error

    can I get the edoc
    also thanks for the help!!

    Leave a comment:


  • adriansto
    replied
    Re: Xerox wc 7125 error

    As I know the IBT dont have ATC sensor.
    Check inside of machine for toner, developer leakage or ,and for gears or clutchs contaminations with toner, developer.
    Service manual only in edoc format.

    Leave a comment:


  • landspeeder
    replied
    Re: Xerox wc 7125 error

    Originally posted by Exok
    Description

    The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
    NOTE:
    • Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to "0". If the machine is not repaired back to normal status, this Fault will occur again during the operation.
    • When turning the power OFF, turn OFF the power switch first and then the main power switch.




    Procedure

    Check the following:
    • The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
    • The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
    • The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
    • The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
    • The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
    • The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
    • The path from Toner Cartridge (K) to Developer (K) for toner blockage
    • The Developer (K) for internal toner blockage
    • The Toner Cartridge (K) for internal toner blockage

    If no problems are found, replace the following parts in sequence:

    Can it be a bad transfer belt as when the machine is running it makes a funny noise which when the belt is turned by hand it sounds the same!! Any chance of getting a service cd copy???
    Color copies are quite faint and black has prtetty much disappeared...comes and goes

    thanks

    Leave a comment:


  • adriansto
    replied
    Re: Xerox wc 7125 error

    Problem with readings from ATC sensor for K.
    Check K toner transport, K dispenser motor, K toner cartridge and developer for blockage, developer K clutch.

    Leave a comment:


  • Exok
    replied
    Re: Xerox wc 7125 error

    Description

    The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
    NOTE:
    • Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to "0". If the machine is not repaired back to normal status, this Fault will occur again during the operation.
    • When turning the power OFF, turn OFF the power switch first and then the main power switch.




    Procedure

    Check the following:
    • The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
    • The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
    • The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
    • The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
    • The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
    • The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
    • The path from Toner Cartridge (K) to Developer (K) for toner blockage
    • The Developer (K) for internal toner blockage
    • The Toner Cartridge (K) for internal toner blockage

    If no problems are found, replace the following parts in sequence:

    Leave a comment:


  • landspeeder
    started a topic Xerox wc 7125 error

    Xerox wc 7125 error

    The error is 092-315 any one have ideas??? Also does any one have a service manual??? sigh

    thanks
Working...