D02-532 Wrong type print cylinder installed

[jeremyb503]

So I have been fighting this one for a while. I have a riso rn2000ui and no matter what drum I install in it I cannot get it to work. I always get the message D02-532 Wrong type print cylinder installed on the screen.

I found a post about changing an option under 588 in service mode but they said to change it to 33 and the display says the range is 1-16.

Any ideas?

Thanks!

[Brave Hart]

So I have been fighting this one for a while. I have a riso rn2000ui and no matter what drum I install in it I cannot get it to work. I always get the message D02-532 Wrong type print cylinder installed on the screen.

I found a post about changing an option under 588 in service mode but they said to change it to 33 and the display says the range is 1-16.

Any ideas?

Thanks!

Enter Test Mode No. 575 (Inking Operation), and press the Start key. The display shows


Enter Test Mode No. 875 (Ink Color), and press the Start key.
Code Color Code Color Code Color Code Color
33 Black 41 Red 4 49 Purple 57 Gold
34 Blue 42 Green 50 Purple 2 58 Gold 2
35 Blue 2 43 Green 2 51 Gray 59 Silver
36 Blue 3 44 Green 3 52 Gray 2 60 Silver 2
37 Blue 4 45 Yellow 53 Light gray 61 Pink
38 Red 46 Yellow 2 54 Light gray 62 Pink 2
39 Red 2 47 Brown 55 Orange 63 Custom
40 Red 3 48 Brown 2 56 Orange 2 64 Color



Code Size Type
3 Black B4
4 Color B4
5 Black A4

6 Color A4

Hope you come rite

[jeremyb503]

Thanks for the reply. I will give it a shot and report back. Thanks, Jeremy

[jeremyb503]

My machine does not have 575 or 875. I have 588 set to 3. 511 - 514 are called INk Cartridge Set SW1, INk Cartridge Set SW2, etc... do I need to change those?

Thanks,

Jeremy

[Brave Hart]

511 to 514 should all be switched on!
587 should be set to 33 if black drum and 64 if a colour drum is used
588 should be set to 3 for 400dpi or 1 for 300dpi
once you set that all run 557 and it should be set.

[jeremyb503]

I go to the options 511-514 and hit start to open the option and then it just beeps and says "In action." How do I actually change the options for these?

Also i have no option 587. The menu skips right from 586 to 588.

Thanks,

Jeremy

[Brave Hart]

I go to the options 511-514 and hit start to open the option and then it just beeps and says "In action." How do I actually change the options for these?

Also i have no option 587. The menu skips right from 586 to 588.

Thanks,

Jeremy

Hi Jeremy

This machine is giving you a hard time !

Ok lets start at the begining

Execute Test Modes Nos. 080 (Clear Error-Status Data),
081 (Clear User Memory),
and 082 (Clear Test-Mode Data Setup).
Run Test Mode No. 588 (Print Drum Code), and enter the code of the currently set print drum if it is a (A4 black drum put in 5 and if it is a colour drum put in 6) If it is a B4 drum put in 3 for black and 4 for colour.
Run Test Mode No. 557 (Inking Action).
Lets see if that works.

[jeremyb503]

I tried those steps and I still get the same message. Any more ideas?

[Brave Hart]

I tried those steps and I still get the same message. Any more ideas?

Ok lets start at the begining.
When did this happen? and what size drum do you have A4 or B4,what colour is this drum?
Have you checked your connector and drum switches?

[jeremyb503]

I believe it started to happen when we installed a drum and got some advice from a technician about how to change the color of the drum to blue instead of black.

I have the factory drum installed now it is black. Is that A3 or B4? I thought originally that we could just change dip switches on this drum just like we did on our GR series machine when we needed to change the color of a drum on that machine. I can't find any switches on this drum. I took the dust cover off and I didn't see any. Is there somewhere else I should look?

I have a different drum that we purchased thinking there was a problem with the black drum (it is a green one) and I get the same error when I install that one.

Thanks,

Jeremy

[Brave Hart]

I believe it started to happen when we installed a drum and got some advice from a technician about how to change the color of the drum to blue instead of black.

I have the factory drum installed now it is black. Is that A3 or B4? I thought originally that we could just change dip switches on this drum just like we did on our GR series machine when we needed to change the color of a drum on that machine. I can't find any switches on this drum. I took the dust cover off and I didn't see any. Is there somewhere else I should look?

I have a different drum that we purchased thinking there was a problem with the black drum (it is a green one) and I get the same error when I install that one.

Thanks,

Jeremy

Hi Jeremy

The problem did start when you changed your black drum in to a colour drum. your black drum Ink Cartridge Set Switch PCB has 5 sensors and your colour PCB has only 3 sensors.

So firstly you will have to go and check and see if it has 5 sensors. put a black cartridge in to your drum just to see if the massage disapears. That way you will know if it is that switches that is giving you the problem. But with all the changes you have made up untill now i will first reset the machine back to its origanal settings and then start doing the checks.

If your black drum is working then you know it can only be switches or a wrong drum type. It might bee that you have a RN2500 drum and not a RN2000/2100 drum

Good luck

[jeremyb503]

The drum that is in the machine now is the original black drum that we got with the machine. It currently has a black cartridge in it.

I would love to reset the setting back to factory. How do I do this? What should the position of the switches be and how do I change them?

[Rens]

Re: D02-532 Wrong type print cylinder installed

Hi,

I know this is an old thread but I'm having the same problem with my RN2000 machine.

I have originally a black drum. Recently I' e bought a used Fluorescent orange + and a Green Drum from the RN Series. The Green one work right out of the box, but the orange one gives this error. I think part of the problem is that the machine registers the drum as a Black drum in the UI and the Green one as color. is There anyway to reset this?

I've read something about techmode/test mode. I've tried getting into that mode, (hold down position buttons while turning on the machine) but the machine doesn't seem to respond any different.

Any thoughts? Tips? Please help!

[Rens]

Re: D02-532 Wrong type print cylinder installed

To anyone with an RN2000 machine; to access test mode hold down line/photo and master test buttons at the same time. couldn't find that anywhere online.

after that; these steps worked for me! Thanks @Brave Hart

Execute Test Modes Nos. 080 (Clear Error-Status Data),
081 (Clear User Memory),
and 082 (Clear Test-Mode Data Setup).
Run Test Mode No. 588 (Print Drum Code), and enter the code of the currently set print drum if it is a (A4 black drum put in 5 and if it is a colour drum put in 6) If it is a B4 drum put in 3 for black and 4 for colour.
Run Test Mode No. 557 (Inking Action).
Lets see if that works.

[then]

Re: D02-532 Wrong type print cylinder installed

Sorry for resurrecting an old thread, but i was having the same error with two color rp drums.
I followed Brave Hearts instructions and it worked for the first drum (a a3 red drum that was set to a4 purple or something?!). But trying with my second drum (green) that gives this error it wont work. I changed the settings, a couple of times, because it seemed they were not retained. Now they are but still gives me the error. Also, in test mode the drum prints fine (test prints) haha

I bought this for cheap online, so im happy with the one drum already, but its weird that the first one works and the second wont.

Any tips? I tried 'resetting' the whole machine (holding the yellow button on startup is that correct?) but it ll just throw the wrong drum error...

Thanks,
then