PDA

View Full Version : Kyocera FS-4000DN "Call Service 0150:"


Custom Search


tp45
10-09-2008, 12:42 AM
I have a FS-4000DN that's giving "Call Service 0150:0077611".

The user had a paper jam and tried to clear it. After that it quit working & displayed the above message... I found the Drum Unit scratched up badly (not sure how). I think they removed it and just beat it up tying to get it back in... Anyway, I've replaced it with NEW drum unit - still get same error.
I've re-seated the toner cartridge many times... but still no luck. There are no signs of any torn paper remaining in the paper path. Without a Service Manual, I'm stuck!
I've been told that the "0150:" indicates needing a firmware upgrade:confused: I find it hard to believe the printer would shut down for just needing a firmware update.

I'm out of ideas, any help would be greatly appreciated!
Tim

blackcat4866
10-09-2008, 12:59 AM
Not quite...
0150:xxxxx is an engine PWB Eeprom error. You can try to flash the engine firmware, but I doubt that it will help. More realistically, replace the engine Eeprom, then flash; or replace the engine PWB.

The event that crashed the firmware could very easily have simultaneously pulled a jam condition. And yes, the machine just can't run without functioning firmware. It's like a computer without an operating system. =^..^=

tp45
10-09-2008, 01:14 AM
Thanks Blackcat... It does make sense if the firmware crashed... I was think it was just wanting an update.
Do you know how I can get the firmware image to try and update either via USB or CF?? I have very limited access to parts and would like to try re-flashing first.

Thanks

10871087
10-09-2008, 01:26 AM
Not quite...
0150:xxxxx is an engine PWB Eeprom error. You can try to flash the engine firmware, but I doubt that it will help. More realistically, replace the engine Eeprom, then flash; or replace the engine PWB.

Agreed, I have seen this one more then one occasion. If a flash doesn't correct the issue you will need an engine board.

10871087
10-09-2008, 01:33 AM
Do you know how I can get the firmware image to try and update either via USB or CF??

PM me your email address and I can get it to you.

aodtech
10-09-2008, 02:03 AM
I had 3900 with this problem. Tech support advised me to do a firmware update as well. It worked. Their explation was that the machine was sensitive to electrical noise. The update would fix that. It worked. Download the firmware, run it and extract it to the root directory on a USB drive, plug it in the machine, turn it on and you should be all set.

flimmer
10-26-2008, 03:05 PM
Update both system and engine firmware - then check if serial. no. and counted pages is printet correct on the status page - if not - you have can try to run SecureExecA4.exe from kyocera to reestablice serial no. and counter

Niessbaer
12-14-2008, 07:05 PM
@10871087

my Kyocera FS in 4000 DN makes the same(identical) goats.
you can send to me please also the firmware image to try and update either via CF ?

This would be very nice from you
many thanks

Niessbaer

TheOwl
12-16-2008, 03:17 AM
Blackcat is right on the money that 0150:xxxxxx is the EEPROM.

Kyocera released a bulletin about this and asked all dealers to upgrade the firmware on these machines whenever a Warranty call was required.

The problem is the machine reading and writing to the EEPROM too frequently which starts to burn out the IC on the EEPROM. The newer firmware slows the rate at which the machine requires to read / write to the EEPROM and also incorporates error handling in the event that this happens anyway.

Once the firmware update has been done, print out a Service Status page and check to see if the machine Serial Number is entered in and the MAC address is correct instead of 00:00:00:00:00:00. If your machine is doing this, you will need a tech to use a recovery program that re-enters this information.

Niessbaer
12-16-2008, 09:30 AM
Hello TheOwl,
thank you for your answer. Can you help me to became this Firmware? Where can I download this? I need them urgently. The FS 4000DN has no more guarantee.
Greetings Niessbaer

Niessbaer
12-19-2008, 10:13 AM
Many thanks for your help. After the Update with the new Firmware the Printer is like a new one.:)
I wish you nice Christmas & a Happy New Year 2009
Regards
Niessbaer

maku
12-20-2008, 12:54 PM
Hello Owl,

I had my FS-4000DN repaired after a "Call Service 0150:....".
I guess they upgraded the software as you described.
However, since then MAC adress is 00:00:00:00:00:00
Since guarantee is expired, I'd like to try to flash the
EPROM by myself.
Do you think that's feasible?

Thanks in advance,

Max

maku
12-21-2008, 06:42 PM
> PM me your email address and I can get it to you.

Please mail firmware for FS-4000DN

Thanks in advance,

Max Kublin (maku)

TheOwl
12-21-2008, 10:48 PM
Maku,

Personally, I would contact the people that repaired your printer and advise them that since the error code, your NIC isn't working. If they are any sort of good service provider, then they will fix this issue free of charge seeing as they missed this the first time and should have been done straight after the firmware update.

If you still have problems, then let me know.

fitsy.13
02-09-2009, 04:24 PM
[quote=tp45;44482]I have a FS-4000DN that's giving "Call Service 0150:0077611".

The user had a paper jam and tried to clear it. After that it quit working & displayed the above message... I found the Drum Unit scratched up badly (not sure how). I think they removed it and just beat it up tying to get it back in... Anyway, I've replaced it with NEW drum unit - still get same error.
I've re-seated the toner cartridge many times... but still no luck. There are no signs of any torn paper remaining in the paper path. Without a Service Manual, I'm stuck!
I've been told that the "0150:" indicates needing a firmware upgrade:confused: I find it hard to believe the printer would shut down for just needing a firmware update.
i had this a few times on this printer tell your customer to push the drum in a bit further if this dont work you need to do the firmware you have a corupted eprom

TheOwl
02-09-2009, 10:30 PM
Fitsy,

There has been alot of information and bulletins provided by Kyocera in regards to this error code. The error "0150" is in regards to an EEPROM error.

This is an extremely common problem on this machine and yes, the firmware upgrade fixes this issue. If you read one of my previous posts on this thread (Page 1), then you understand why the error occurs.

florin0904
01-23-2010, 09:36 PM
Sorry my english is not very good, i'm sorry if i upset anyone. I have a kyocera FS-4000DN with a Call Service 0150:0000000 error, i don't know how to fix this problem can someone please help me. Thanks in advance. Have a nice day.

Niessbaer
01-24-2010, 12:47 PM
Hy florin0904

You also can speak with me in german :D
You need a firmware upgrade.
Tell me your Emailadres and I send the firmware to you.

Niessbaer

meimantas
05-23-2011, 12:34 PM
Hello,
The printer fs-4000dn show 0150:0000000 error.. Can anybody send me firmware for this printer to email? meimantas@gmail.com. Thanks

JustManuals
05-23-2011, 06:26 PM
1st post and wants something, what a surprise!

danito
03-18-2015, 07:36 PM
I need firmware for Kyocera FS-4000 can you give?
danut.petria@yahoo.ro

Niessbaer
03-20-2015, 07:43 PM
I need firmware for Kyocera FS-4000 can you give?
danut.petria@yahoo.ro


I sent you an e-mail :cool::)

Greetings Andreas

danito
03-20-2015, 08:07 PM
I sent you an e-mail :cool::)

Greetings Andreas

thanks so much

Sparrowenterprises2004
10-15-2015, 08:18 PM
I also need the firmware update for the kyocera ecosys fs-4000dn printer. Please email file to sparrowenterprises2004@yahoo.com Am receiving the 150 error and the printer is in supervisor mode waiting on Parallel status message. If possible please send instructions for updating the eeprom. Thank you in advance. Need this quickly as my client is waiting to get this fixed. Again Thank you for your help.

jchavez
03-25-2017, 03:28 AM
necesito el firmware para una impresora fs-4100dn me lo podrian proporcionar a mi correo jchavezpatlan@gmail.com

tecaldryn
04-27-2017, 08:41 PM
HiI bought a Kyocera FS-4000, which was working normally and from one day to the other an error appeared when connecting and it presents the error F-050 and it does not let me do any service in the panel. I've already been told it may be the equipment system.Can someone help me with this system?Thanks in advance :(
HiI bought a Kyocera FS-4000, which was working normally and from one day to the other an error appeared when connecting and it presents the error F-050 and it does not let me do any service in the panel. I've already been told it may be the equipment system.Can someone help me with this system?Thanks in advance

dominicbogecho
10-19-2017, 04:03 PM
Re: Kyocera FS-4200DN "Call Service 0150:"
I also need the firmware update for the kyocera ecosys fs-4200dn printer. Please email file to dominicbogecho@gmail.com Am receiving the 150 error on the screen. If possible please send instructions for updating the eeprom. Thank you in advance. Pleasehelp me. Again Thank you for your help.

dominicbogecho
10-31-2017, 12:58 PM
Hy florin0904

You also can speak with me in german :D
You need a firmware upgrade.
Tell me your Emailadres and I send the firmware to you.

Niessbaer


please help me with kyocera fs-4200dn firmware update. will be very much glad if you asisted.
my email is : dominicbogecho@gmail.com

msh111
05-29-2021, 09:35 AM
> PM me your email address and I can get it to you.

Please mail firmware for FS-4000DN

Thanks in advance,

Max Kublin (maku)

Hallo,
The printer fs-4000dn show 0150:0000000 error.. Can anybody send me firmware for this printer to email? mahdi.shy@gmail.com

ich bedanke mich im Voraus.

Phil B.
05-29-2021, 03:53 PM
Hallo,
The printer fs-4000dn show 0150:0000000 error.. Can anybody send me firmware for this printer to email? mahdi.shy@gmail.com

ich bedanke mich im Voraus.

this thread is over 6 years old... your best bet is to start your own new thread stating when problem started and all that you've tried.

dalewb74
06-17-2021, 11:40 PM
target practice then buy a new printer.....

Custom Search