canon ir 1018 download standby

[montana]

hi...i need help for canon ir1018...this machine displaying download standby...anyone has the firmware for this machine?
i have the ir2016-2020 firmware but i don't know if it is work with ir 1018.....
thank you

[doktor]

No way!!!

[Caldo]

You should start looking for firmware for your model IR1018.

[CanonSco]

hi...i need help for canon ir1018...this machine displaying download standby...anyone has the firmware for this machine?
i have the ir2016-2020 firmware but i don't know if it is work with ir 1018.....
thank you

Is this a variant of the IR1022?

If so, then I have had 2 give me that symptom. I am working from memory here, but there is a jumper under the CMOS battery on the controller that you can short to get out of download mode.
I will look it up when I get a chance to fire the work laptop up.
I am now off to drink lots of Highland Park Whisky with some local Belhaven Best beer to chase it

[montana]

hi...thanks guys..mr canonsco thank you for reply ..yes it is a variant of the ir 1022..is this jumper locating on DC controller?so there is no need for firmware if this short work...
thank you
best regards

[jobert]

Same problem...tnx guys..

[teckat]

hi...thanks guys..mr canonsco thank you for reply ..yes it is a variant of the ir 1022..is this jumper locating on DC controller?so there is no need for firmware if this short work...
thank you
best regards

imageRUNNER 1023iF / 1023N / 1023

Machine powers up and Download Mode is displayed
Short the two pins at JP141 on the Image Processor Board. This can be done
with a screwdriver or an alligator clip.
This will reset the machine so system software can be re-flashed.
PIN.JPG

[montana]

thank you very much indeed mr teckat for the help info...i will try it.but there is a question please should i reload a new firmware after short the pins...if yes where it is can be found?
thank you again...best regards...

[teckat]

thank you very much indeed mr teckat for the help info...i will try it.but there is a question please should i reload a new firmware after short the pins...if yes where it is can be found?
thank you again...best regards...

you do not need to re-load firmware/

short pin method could jump u out of that download screen issue
report back if issue is not fixed

[montana]

thanks ...i will try and let you know my dear..................

[silverink]

Short-out , same problem

you do not need to re-load firmware/

short pin method could jump u out of that download screen issue
report back if issue is not fixed

Hello

I have an Canon IR 1018 and displays "DOWNLOAD STANDBY " when i power it on .
I have shorted out the 2 pins on the JP141 jumper an i have the same problem "DOWNLOAD STANDBY " .

At one startup it did work , and the printer started fine . After shutdown , the same problem . I pulled out the DDR card , and putted back , and the same issue.

Any suggestions ??

Thank in advance

[betatech]

same problem

Hello,

I'm a tech of a lab located in an happy island


We got two iR1018, one is working good, the other asks for firmware.
We checked the cr2032, is 3v+ - shorted all the JPs with no change. While shorting JP141 just skips the bad firmware and asks for flash quickly.

We got SST4.33 but we can't find anywhere the flash file (should it be 16m?), we think we can download the flash from the good ir1018, but we can't configure correctly the usb device in WinXP.

Anybody experienced this before?

Thanks a lot in advance,

We are available for answering about other electronics repair (lcd, tv, pc/nb mobos, etc)

We know this is our first post, but we just found this forum by googling and it seems very good so we just registered. We we could help, we will.


-added infos:
ddr is good
reads usb thumb drive (fat32, 1gb) --> could we load firmware from here?

[teckat]

I believe these models use same compatible Firmware>
iR1018, iR1022, iR1022A, iR1022F, iR1022i, iR1022iF, iR1023, iR1023iF, iR1023N = Flash ROM 16MB type

(1) If upgrading from an older version to v60.03 (or later), the BOOT area is increased.
At the same time, the SYSTEM writing start address (FLASH-ROM) is changed.
The SYSTEM writing start address is included in the BOOT v60.03 and later, so after BOOT has completed
downloading, turn OFF and ON the power so that the new SYSTEM writing start address is reflected.


Upgrade procedures
<Without options>
1. Overwrite BOOT.
2. Check that "OK" appears on the touch panel display. Then, turn OFF and ON the power manually.
(Download mode starts.)
3. Overwrite SYSTEM.

<With OPT16MB>
1. Overwrite BOOT.
2. Check that "OK" appears on the touch panel display. Then, turn OFF and ON the power manually.
(Download mode starts.)
3. Overwrite OPT16.
4. Check that "OK" appears on the touch panel display. Then, turn OFF and ON the power manually.
(Download mode starts.)
5. Overwrite SYSTEM.

<With OPT32MB>
1. Overwrite BOOT.
2. Check that "OK" appears on the touch panel display. Then, turn off and on the power manually.
(Download mode starts.)
3. Overwrite OPT32
4. Check that "OK" appears on the touch panel display. Then, turn off and on the power manually.
(Download mode starts.)
5. Overwrite SYSTEM.

[betatech]

Thank you very much for your detailed instructions. I'm having troubles in finding any of that firmwares. Also, I can't find usb drivers (I think they are in the firmware disc)

Does anybody know where can I download the firmware?

[teckat]

Thank you very much for your detailed instructions. I'm having troubles in finding any of that firmwares. Also, I can't find usb drivers (I think they are in the firmware disc)

Does anybody know where can I download the firmware?

what MODEL firmware ver is on SST