Ricoh AP 610N with SC760 error

[patterson70]

Hello, has anyone run into this code SC760 on an AP610N?
I cannot find any direct info about this, just general suggestions.
I know this printer is old. Does anyone still have these in the field?
Not sure if it worth pursuing.

[UNICORNico]

Re: Ricoh AP 610N with SC760 error

Are you sure the error code is "SC760"?
According to the manual we have, that code does not exist.

[slimslob]

Re: Ricoh AP 610N with SC760 error

Not specifically shown in Goose's Guide for the AP 610, but for other printers, it has to do with the finisher punch motor.

G133	SC 760	Finisher punch motor error - check/clean/replace punch HP sensor (chads)
G133	SC 760	Finisher punch motor error - check for binds slowing motor
G133	SC 760	Finisher punch motor error - check connections to punch unit
G148	SC 760	Finisher punch motor - Motor bound / obstruction
G148	SC 760	Finisher punch motor - Motor defective
G148	SC 760	Finisher punch motor - Punch HP sensor defective
G148	SC 760	Finisher punch motor - Check harness and connections
G179	SC 760	Finisher punch motor error - check/clean/replace punch HPS
G179	SC 760	Finisher punch motor error - check for mechanical binds overloading motor

[patterson70]

Re: Ricoh AP 610N with SC760 error

Not specifically shown in Goose's Guide for the AP 610, but for other printers, it has to do with the finisher punch motor.

G133	SC 760	Finisher punch motor error - check/clean/replace punch HP sensor (chads)
G133	SC 760	Finisher punch motor error - check for binds slowing motor
G133	SC 760	Finisher punch motor error - check connections to punch unit
G148	SC 760	Finisher punch motor - Motor bound / obstruction
G148	SC 760	Finisher punch motor - Motor defective
G148	SC 760	Finisher punch motor - Punch HP sensor defective
G148	SC 760	Finisher punch motor - Check harness and connections
G179	SC 760	Finisher punch motor error - check/clean/replace punch HPS
G179	SC 760	Finisher punch motor error - check for mechanical binds overloading motor

Oh sorry, I meant SC670

[slimslob]

Re: Ricoh AP 610N with SC760 error

Oh sorry, I meant SC670

670 Engine response error

• Engine board installed incorrectly
• Engine board defective
• Controller board defective

G091/G094/G095/G112-G116	SC 670	Engine response error: Defective engine board
G091/G094/G095/G112-G116	SC 670	Engine response error: Defective controller

Since neither of those boards are likely to be still available unless you have a loose connection your out of luck

[patterson70]

Re: Ricoh AP 610N with SC760 error

670 Engine response error

G091/G094/G095/G112-G116	SC 670	Engine response error: Defective engine board
G091/G094/G095/G112-G116	SC 670	Engine response error: Defective controller

Since neither of those boards are likely to be still available unless you have a loose connection your out of luck

Thank for this. I was hoping someone has had this code and it turned out to be a loose connection.
As a matter of fact, has anyone seen this error code at all?
And if so was it a board or just a connection?
I know this is a reach being an older model.

[slimslob]

Re: Ricoh AP 610N with SC760 error

With newer MFPs it is usually the USB cable between the controller and the display.

[patterson70]

Re: Ricoh AP 610N with SC760 error

With newer MFPs it is usually the USB cable between the controller and the display.

Is the loose connection more at the display? Maybe the machine gets rough handled and the cable loosens up there?
If so then you have to remove the display to get to it?

[slimslob]

Re: Ricoh AP 610N with SC760 error

Is the loose connection more at the display? Maybe the machine gets rough handled and the cable loosens up there?
If so then you have to remove the display to get to it?

My experience has been at the controller. Unplug and reconnect usually takes care of the error.

[UNICORNico]

Re: Ricoh AP 610N with SC760 error

In my opinion, this type of "connection failure" may be due to microparticles that accumulate over time or some type of static interference.


I'm glad to read that the problem was resolved.

[anothertech]

Re: Ricoh AP 610N with SC760 error

In my opinion, this type of "connection failure" may be due to microparticles that accumulate over time or some type of static interference.


I'm glad to read that the problem was resolved.

Who said it was fixed? I didn't see it

[UNICORNico]

Re: Ricoh AP 610N with SC760 error

I misunderstood, sorry for the confusion.