Page 1 of 3 123 LastLast
Results 1 to 10 of 23
  1. #1
    Junior Member
    Join Date
    Mar 2010
    Location
    dieppe
    Posts
    9
    Post Thanks / Like
    Rep Power
    0

    How to Execute ECD Program for Samsung CLX-3175FN

    Hi,
    sorry to bother you all but if someone can tell me how to Execute the ECD program for my Samsung CLX-3175FN i would more than just appreciate. I have the service manual but it doesn't tell how to activate EDC it just says Execute EDC Program that s it...please help


  2. #2
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,741
    Post Thanks / Like
    Rep Power
    161
    EDC Mode uses a small piece of software on your laptop to communicate via the USB connection to the printer. Earlier levels of firmware allow use of EDC Mode. Later production allows only SmartPanel or Web Interface access.

    Don't overestimate the usefulness of EDC mode. If there is a system error you will not be able to use EDC mode. It's generally not very useful.

    You should have no difficulty finding the EDC software or SmartPanel software. SmartPanel is generally a better diagnostic tool. What sort of problem are you trying to diagnose? I've worked on a lot of the CLP-315/CLP-315W/CLX-3175FN series machines. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  3. #3
    Junior Member
    Join Date
    Mar 2010
    Location
    dieppe
    Posts
    9
    Post Thanks / Like
    Rep Power
    0
    Hi Blackcat 4866,

    I have my sensor problem but would like to test all the rest of my sensors so that s why i would really like to have the EDC soft that samsung work with since i got the menu in the service manual but if it is not possible i m willing to try smart panel as you mentionned but got no idea where to get those 2 tools? i m passing and order so i want to test ALL the printer component before passing my order to the electronic store ,thanks again and much appreciate !!!!

    Eric


  4. #4
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,741
    Post Thanks / Like
    Rep Power
    161
    EDC won't help with that, neither will SmartPanel. SmartPanel will display "Paper Jam 1". The diagnostic modes for this machine are next to useless. The only way to test out that particular sensor is to meter out the 5vdc output from the exit sensor. You can try to bend a couple of paper clips to use as leads to reach pins #1 & #3 at the sensor or at the HVT connector. Anything over 3.2 vdc is a high reading, anything below 3.0 is a low reading. (Typically ranges from 3.6vdc high to 0.3vdc low)

    Or you could just trust me. I've changed over 75 of these sensors, and have never seen another cause. It is a lot easier to diagnose this problem on a CLP-315 (the printer version). You can pop the top off and pin out the sensor all you like. On the CLX-3175 its considerably harder to get to the pins.

    If you still want the software just google "EDC Samsung" or "Smart Panel Samsung CLX-3175". www.nodevice.com is a good source for most printer related software. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  5. #5
    Junior Member
    Join Date
    Mar 2010
    Location
    dieppe
    Posts
    9
    Post Thanks / Like
    Rep Power
    0
    i'm trying to run the appz on my pc (vista 64 bit) but get the write error, error. I guess it is because i got an error on my printer? or because i m using 64bit OS? or because i m stupid ..lol , thanks


  6. #6
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,741
    Post Thanks / Like
    Rep Power
    161
    It doesn't matter why. It won't help you test sensors. I hope I haven't mislead you. EDC software will not help diagnose a bad sensor, and may not function at all on later levels of firmware. Please don't waste your time with it. =^..^=

    Last edited by blackcat4866; 03-14-2010 at 04:13 PM.
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  7. #7
    Junior Member
    Join Date
    Mar 2010
    Location
    dieppe
    Posts
    9
    Post Thanks / Like
    Rep Power
    0
    i'm waiting impatiently for my part to come in
    i removed all panel , left , right and top i see my fuser perfectly but i m wondering where is that ''Exit sensor'' ? i searched all over the web to try to find out a picture of that sensor ...nothing. Also, i ordered the part from Global Electronics ...
    0604-001393 PHOTO-INTERRUPTER 1 $1.61and i hope it is the right thing....

    thank you


  8. #8
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,741
    Post Thanks / Like
    Rep Power
    161
    That is the correct item. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  9. #9
    Junior Member
    Join Date
    Mar 2010
    Location
    dieppe
    Posts
    9
    Post Thanks / Like
    Rep Power
    0
    Problem fixed with the help of blackcat 4866


  10. #10
    Junior Member
    Join Date
    Jul 2010
    Posts
    2
    Post Thanks / Like
    Rep Power
    0

    SAMSUNG CLX 3175 continuously looping reset

    After sending some multiple recipient fax, it suddenly froze, once restarted, it keeps looping a restart with following error messages:

    Warming up
    FAX SSM...
    Interna Error

    and again and again

    Any suggestion on how to reset it to factory defaults?

    Thanks, Guido


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here